Create an extreme temperature life energy wheel checklist.

Source excerpt

## ［ 3. MACHINE OPERATION ］ ## 2. Operation in Extreme Heat - a. Use an engine oil, hydraulic oil and fuel oil designed for use in hot climates. Also, keep battery fully charged. - b. Clean radiator, oil cooler and debris screen often to prevent damage or overheating of the machine. - c. Keep all belts properly tensioned. - d. Make certain that the engine coolant mixture is sufficient to keep the machine safe. - e. If the machine becomes overheated, idle the machine to help cool the engine, turn engine "OFF" and check coolant level. After filling to proper level the machine continues to over heat, stop engine, allow to cool, drain and flush entire cooling system and refill with the proper mixture of fresh, clean coolant. - f. Check the battery electrolyte (acid) level frequently and fill as necessary with distilled water. - g. Keep a close watch on the gauge cluster for warning icons during operation. Avoid unnecessary low speed running of the engine during operation. During slow, or no work periods, place throttle potentiometer in "LO" idle position. <!-- image --> In regard to above b.: Do not allow dirt and debris to accumulate in the radiator fins, oil cooler fins or debris screen. ## 3. Operation in High Altitudes - a. Due to low atmospheric pressure at high altitudes, a decrease in engine power will be experienced. Be aware of this fact when placing machine under heavy load in high altitude climates. - b. Keep close watch on the engine temperature gauge to avoid overheating of the engine. ## 4. Operation in Sandy and Dusty Areas - a. Check the engine air cleaner elements frequently in sandy or dusty conditions. - b. When air cleaner restriction lamp is lit, change filters immediately regardless of time intervals. - c. Service fuel filter, water separator, and all hydraulic filters frequently. ## 5. Operation at Seashore or Salty Climate - a. Thoroughly wash machine daily to help avoid corrosion of machined areas, electrical components and cylinder r…

Source excerpt

## Extremes of temperature 23 (1) Where an employee is exposed to work condi -tions that may present a hazard because of excessive heat, an employer shall ensure that a competent person instructs the employee in the significance of symptoms of heat stress such as heat exhaustion, dehydration, heat cramps, prickly heat and heat stroke and in the precau -tions to be taken to avoid injury from heat stress. 23 (2) Where an employee is exposed to work condi -tions that may present a hazard because of excessive cold, an employer shall ensure that a competent person instructs the employee in the significance of symptoms of cold stress such as severe shivering, pain in the ex -tremities of the body and reduced mental awareness and in the precautions to be taken to avoid injury from cold stress. ## Threshold Limit Values for Formaldehyde and Lead Sulfide Repealed: 2022-27 2001-33; 2022-27 ## Threshold limit value for formaldehyde Repealed: 2022-27 2022-27 23.1 Repealed: 2022-27 2001-33; 2022-27 ## Air Contaminants and Industrial Ventilation 2022-27; 2022-79 ## Air contaminants - level of concentration 2022-79 24 (1) An employer shall ensure that an air contami -nant is kept at a level of concentration that does not con -stitute a hazard to the health or safety of an employee ex -posed to it and, if an occupational exposure limit exists in respect of an air contaminant, that the exposure of the employee to the air contaminant at no time exceeds the occupational exposure limit. Chemical Substances and Physical Agents and Biolo -gical Exposure Indices ». 2001-33; 2022-27 ## Températures extrêmes 23 (1) Lorsque les conditions de travail d'un salarié peuvent l'exposer au danger de chaleur excessive, l'em -ployeur doit s'assurer que le salarié reçoit les instruc -tions d'une personne compétente sur la signification des symptômes de stress dû à la chaleur tels que l'épuise -ment dû à …

Source excerpt

## 3.1.18 MACHINE OPERATION IN ADVERSE WEATHER CONDITIONS ## 1. Operation in Extreme Cold - a. Follow procedures in the section "3.1.7.B Start Up in Cold Conditions" as starting engine may be difficult due to extremely cold temperatures - b. Use an engine oil, hydraulic oil and diesel fuel designed for use in cold climates. See maintenance section, "4.3 LUBRICANT, FUEL &amp;amp; COOLANT SPECIFICATIONS" for reference. Also, keep battery fully charged. - c. Make certain to perform machine warm-up procedures as described in the section "3.1.7 STARTING ENGINE" to prevent premature wear or damage to pumps, motors and other components. - d. Make certain that the engine coolant mixture is sufficient to keep the machine safe. Take into consideration wind chill factors when mixing coolant ratios. - e. Keep battery terminals free of ice and snow. Ice and snow could cause the terminals to short circuit and cause extensive damage to the machine systems. Check the battery electrolyte (acid) level frequently and fill as necessary with distilled water. If the machine will be left outside overnight, it is recommended to remove the batteries and store in a warm area. In regard to above c.: In extremely frigid climates, covering the radiator is a method to aid the machine warm-up. IF NECESSARY TO MAINTAIN OPERATING TEMPERATURES, COVER THE OUTER EDGES OF THE RADIATOR, LEAVING AN OPENING IN THE CENTER PART OF THE COVER - THUS AVOIDING FAN OVERLOADING. Keep a close watch on the gauge cluster for warning icons during operation. It may be necessary to use a coolant heater, fuel heater, engine heater jacket, and/or additional battery power to aid engine starting. In regard to above d.: Mix coolant to a protection temperature of 5C degrees (9F degrees) lower than the machine will experience during operation, storage or transport. ３

Source excerpt

5. Pull up safety lock lever (4) to "LOCKED (UP)" position. 6. When necessary to leave from the machine, close windows, cab door and each door, and then lock it. <!-- image --> ## 3.1.17 PRECAUTIONS AFTER OPERATION Check engine coolant level, engine oil pressure and fuel level for shortage through the use of multi-display. - 1. If warnings of engine coolant and engine oil pressure are displayed, move the machine to a safe place and stop the engine. And then repair it according to applicable procedure in Chapter 4 "INSPECTION &amp;amp; MAINTENANCE CHART". - 2. Check for any oil or coolant leakage. Check the attachment, exterior, and travel system components. If leakage and damage are found, repair it immediately according to applicable procedure in Chapter 4 "INSPECTION &amp;amp; MAINTENANCE CHART". - 3. Fully refill with fuel. However, do not overfill (to the top of the tank) to avoid overflowing due to fluid expansion under normal temperature. - 4. Remove mud, etc., stuck to the traveling components. <!-- image -->

Source excerpt

## Eye Protection - 229 Eye and face protectors - 230 Contact lenses - 231 Electric arc welding ## Flame Resistant Clothing ## 232 Use of flame resistant clothing ## Foot Protection ## 233 Footwear ## Head Protection - 234 Protective headwear - 235 Bicycles and skates - 236 All-terrain vehicles, snow vehicles, motorcycles - 237 Firefighters - 238 Bump hat - 239 Exemption from wearing headwear ## Life Jackets and Personal Flotation Devices - 240 Compliance with standards - 241 Use of jackets and flotation devices ## Limb and Body Protection - 242 Limb and body protection - 243 Skin protection ## Respiratory Protective Equipment - 244 Respiratory dangers - 245 Code of practice - 246 Approval of equipment - 247 Selection of equipment - 248 Storage and use - 249 Quality of breathing air - 250 Effective facial seal - 251 Equipment for immediate danger - 252 Equipment - no immediate danger - 253 Air purifying equipment - 254 Emergency escape equipment - 255 Abrasive blasting operations ## Part 19 ## Powered Mobile Equipment ## 256 Operator responsibilities

Source excerpt

## Temperature ## Temperature - 21 (1) Subject to subsection (2), an employer shall en -sure that the temperature of a work area in an enclosed place of employment is maintained as follows: - (a) where light work is performed while sitting, such as any mental work, precision work, reading or writing, the minimum temperature required is 20 °C; - (b) where light physical work is performed while sitting, such as electric machine sewing or work with small machine tools, the minimum temperature re -quired is 18 °C; - (c) where light or moderate physical work is per -formed while standing, such as machine tool work, assembly work or trimming, the minimum tempera -ture required is 16 °C; and - (d) where heavy physical work is performed while standing, such as drilling or manual work with heavy tools, the minimum temperature required is 12 °C. - 21 (2) If is not practical to heat a work area to the tem -perature required by subsection (1), an employer shall provide a suitable place where the employee may go to get warmed. 2022-27 ## Extremes of Temperature ## Extremes of temperature - 22 Where an employee is exposed to work conditions that may present a hazard because of extreme heat or ex -treme cold, an employer shall ensure that - (a) a competent person measures and records the thermal conditions at frequent intervals and makes the findings available to a committee, if any, and to an of -ficer on request, and - (b) the occupational exposure limits for protection against heat stress and cold stress are followed as well as the work-rest regimen for heat, the work-warming regimen for cold and other advice found in the AC -GIH publication entitled '2016 Threshold Limit Val -ues for Chemical Substances and Physical Agents and Biological Exposure Indices'. 2001-33; 2022-27 ## Température ## Température - 21 (1) Sous réserve du paragraphe (2), l'employeur doit s'assurer que la température de l'aire de travail dan…