GFCI and Assured Grounding in BC
A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.
Rosie's answer
Published by SALUSWhen used outdoors or in wet or damp locations, portable electrical equipment, including temporary lighting, must be protected by an approved ground fault circuit interrupter (GFCI) of the Class A type installed at the receptacle or on the circuit at the panel, unless another acceptable means of protection is provided. A ground fault circuit interrupter must not be used in place of grounding except as permitted by the Electrical Safety Regulation. [1]
Portable electrical equipment, required to be grounded and not permanently connected to the wiring system, must be effectively grounded by the use of approved cords and polarized plugs inserted in grounded polarized receptacles. [1]
Sources used for this answer
[1] Occupational Health and Safety Regulation (B.C. Reg. 296/97)
Page 384
Open source documentSource excerpt
# OCCUPATIONAL HEALTH AND SAFETY REGULATION (cont.) ## Identification of controls (cont.) B.C. Reg. 296/97 WORKERS COMPENSATION ACT # OCCUPATIONAL HEALTH AND SAFETY REGULATION Part 19 - Electrical Safety (3) Portable electrical equipment, required to be grounded and not permanently connected to the wiring system, must be effectively grounded by the use of approved cords and polarized plugs inserted in grounded polarized receptacles. [am. B.C. Reg. 312/2003, App. E, S. 13.] ## Ground fault circuit interrupters - 19.15 (1) When used outdoors or in a wet or damp location, portable electrical equipment, including temporary lighting, must be protected by an approved ground fault circuit interrupter of the class A type installed at the receptacle or on the circuit at the panel, unless another acceptable means of protection is provided. (2) A ground fault circuit interrupter must not be used in place of grounding except as permitted by the Electrical Safety Regulation. [am. B.C. Reg. 312/2010, App. M, S. 2.] ## Working on High Voltage Electrical Equipment ## Isolation and lockout - 19.16 (1) High voltage electrical equipment must, if practicable, be completely isolated, grounded, and locked out as required by this Regulation before starting work on it. (2) If it is not practicable to completely isolate high voltage electrical equipment, (a) written safe work procedures acceptable to the Board must be followed, (b) two or more qualified and authorized persons must be present while the work is being done, unless the procedures being followed under paragraph (a) specifically permit the work to be done by one person, (c) appropriate electrical protective equipment, including rubber blankets, hoses, hoods, gloves and live line tools must be selected, used, stored, tested, and maintained in accordance with a standard acceptable to the Board, and (d) the use of metal ladders, wire reinforced side rail wooden ladders, metal scaffolds or metal work platf…
Keep exploring.
Electrical panel removal in older building
Toolbox Talk: Electrical Panel Removal in Older Buildings *Date:** [DATE] *Duration:** [DURATION] minutes *Presenter:** [PRESENTER NAME] *Location:** [LOCATION] Objective To ensure the safe removal of electrical panels in older buildings by understanding the associated hazards and implementing effective control
Read the threadretirement facility interior renovation whilst occupied
Interior renovation or refurbishment in an occupied retirement facility or aged care residence should be managed as a live-environment construction project with vulnerable occupants, so the core approach is to separate residents from the work, identify all hazards before work starts, control dust, noise, infection
Read the threadWrite a toolbox talk on HVAC rooftop units and cranes
Toolbox Talk: HVAC Rooftop Units and Crane Safety *Date:** [DATE] *Duration:** [DURATION] minutes *Presenter:** [PRESENTER NAME] *Location:** [LOCATION] Objective The objective of this toolbox talk is to ensure the safe operation and maintenance of HVAC rooftop units using cranes. Participants will learn about the
Read the threadperform a risk assessment on fall protection over unenergized electrical gear
A risk assessment for fall protection over unenergized electrical gear must consider several factors to ensure worker safety. Here's a breakdown of potential hazards, risks, and control measures: *Hazards:** Falls from height: Working at height near electrical gear always presents a fall hazard, whether from a
Read the threadGive me a checklist for a crane
Crane Safety Checklist Purpose This checklist is designed to ensure the safe operation and maintenance of cranes. It covers pre-operation, during operation, and post-operation checks to identify potential hazards and ensure compliance with safety standards [1]. Instructions Complete this checklist before each shift and
Read the threadIf you squint properly, do you need to wear a welding helmet
Eye and Face Protection for Welding and Similar Operations ========================================================== This document outlines the required safety measures, including appropriate eye and face protection, to prevent injury when performing tasks that may expose the eyes to intense light or sparks, such as
Read the threadAdd your experience.
Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.
New contributions are temporarily closed while the moderation queue is configured.
Community answers(0)
No community answers have been approved yet.
Comments on Rosie's answer(0)
No comments have been approved yet.