Asked by a personGeneral — US and Canadaen-CA

walk path maintenance

A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.

Rosie's answer

Published by SALUS

Here is a safety checklist for walk path maintenance, incorporating elements from the provided documents:

Walk Path Maintenance Safety Checklist

Purpose: To ensure walk paths are safe and well-maintained for all personnel.

Instructions: Inspect all walk paths regularly and complete this checklist. Mark each item as either 'Yes' (compliant), 'No' (non-compliant), or 'N/A' (not applicable). If any item is marked 'No', initiate corrective action immediately.

I. General Conditions

[ ] Cleanliness: Are all walk paths free from trash, debris, and unnecessary obstructions? [1]
[ ] Orderliness: Are materials and equipment stored properly to prevent tripping hazards? [1]
[ ] Sanitation: Are walk paths maintained in a sanitary condition to prevent exposure to health hazards? [1]

II. Surface Conditions

[ ] Dryness: Are walk path surfaces maintained in a dry condition to the extent feasible? [1]
[ ] Hazard-Free: Are walk paths free of sharp or protruding objects, loose boards, corrosion, leaks, spills, snow, and ice? [1]
[ ] Non-Slip: Are effective means in place to minimize slipping, especially around machines or wet processes? [2]
[ ] Load Support: Can each walking-working surface support the maximum intended load? [1]

III. Walkway Specifics

[ ] Width: Are walkways of sufficient width to provide adequate passage and working areas? [2]
[ ] Even Flooring: Are walkways evenly floored and kept in good repair? [2]
[ ] Elevated Walks: Are elevated walks (4 feet or more from the floor level) provided with standard railings? [2]
[ ] Toeboards: If elevated walks exceed 6 feet, are standard toeboards provided to prevent material from falling? [2]

IV. Stairways (If Applicable)

[ ] Construction: Are stairways constructed according to safety standards? [2]
[ ] Handrails: Are stairways provided with standard handrails on at least one side (or both sides if wider than 4 feet)? [2]
[ ] Lighting: Are all stairways adequately lighted? [2]

V. Ramps (If Applicable)

[ ] Slope: Does the ramp have a maximum slope of 1/6? [3]
[ ] Non-Slip Surface: Is the ramp equipped with a non-slip surface or cleats? [4]
[ ] Guardrails: If the ramp is greater than 1.8 m in rise, does it have a guardrail and supporting structure on any open side? [4]
[ ] Plank Fastening: If planks are used, are they securely fastened together? [4]
[ ] Minimum Width: Does the ramp have a minimum width of 450 mm? [4]
[ ] Load Capacity: Is the ramp able to withstand 4 times the maximum load likely to be imposed on the ramp? [4]

VI. Catwalks (If Applicable)

[ ] Guardrails: Is the catwalk equipped with a guardrail? [5]
[ ] Load Capacity: Is the catwalk able to withstand 4 times the maximum load likely to be imposed on it? [5]

VII. Excavator Specifics

[ ] Steps, Walkways, and Handholds: Inspect the steps, the walkways, and the handholds. [6]
[ ] Cleanliness: Clean the steps, the walkways, and the handholds. [6]
[ ] Repairs: Make any necessary repairs to the steps, walkways, and handholds. [6]

VIII. Corrective Actions

[ ] Describe any hazards found during the inspection:
[ ] Corrective actions taken:
[ ] Further actions needed:

IX. Inspection Details

Date of Inspection:
Inspected By: (Print Name)
Signature: ___________________________

X. Follow-Up

Date of Follow-Up:
Completed By: (Print Name)
Signature: ___________________________

6 source record(s)

Sources used for this answer

[1] Occupational Safety General Regulations (N.S. Reg. 44/99)

Page 79

Open source document

Source excerpt

- 143A For purposes of Sections 144 and 145, 'ramp' means a ramp designed primarily for pedestrian use. Section 143A added: O.I.C. 2000-130, N.S. Reg. 52/2000. 144 - (1) Subject to subsections (2) and (3), an employer shall ensure that a permanent ramp is designed, constructed and maintained in accordance with the National Building Code of Canada , as adopted and modified under the Building Code Act and the Nova Scotia Building Code Regulations made under that Act . - (2) Where the National Building Code of Canada , as adopted and modified under the Building Code Act and the Nova Scotia Building Code Regulations made under that Act does not apply to a permanent ramp built after this Section comes into force, an employer shall ensure that the permanent ramp - (a) meets or exceeds the requirements of Section 145; or - (b) is certified by an engineer as having been constructed in accordance with the certified design of an engineer. - (3) Where - (a) the National Building Code of Canada , as adopted and modified under the Building Code Act and the Nova Scotia Building Code Regulations made under that Act does not apply to a permanent ramp built before this Section comes into force; and - (b) there is a reasonable doubt as to whether the permanent ramp is adequate, - an employer shall ensure that an engineer provides a written assessment of the permanent ramp. - (4) Where a written assessment required under subsection (3) identifies an inadequacy, an employer shall ensure that - (a) the ramp is removed; or - (b) modifications are made and are certified by an engineer as having been made in accordance with the certified design of an engineer. Section 144 amended: O.I.C. 2013-65, N.S. Reg. 53/2013. - 145 (1 ) An employer shall ensure that a temporary ramp - (a) has a maximum slope of 1/6; \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_

[2] Occupational Safety General Regulations (N.S. Reg. 44/99)

Page 81

Open source document

Source excerpt

constructed in accordance with the certified design of an engineer. - (4) An employer shall ensure that a temporary catwalk - (a) has a minimum clear width of 450 mm; - (b) is equipped with a guardrail in accordance with the requirements for a guardrail in subsection 142(4); and Clause 146(4)(b) amended: O.I.C. 2000-130, N.S. Reg. 52/2000. - (c) is able to withstand 4 times the maximum load likely to be imposed on it. Subsection 146(5) repealed: O.I.C. 2000-130, N.S. Reg. 52/2000. ## Ladders - 147 An employer shall ensure that a fixed ladder is designed, constructed, installed and maintained in accordance with the latest version of ANSI standard ANSI A14.3 'American National Standard for Ladders - Fixed - Safety Requirements'. Subsection 147 amended: O.I.C. 2013-65, N.S. Reg. 53/2013. - 148 (1 ) An employer shall ensure that a portable ladder used at a workplace is - (a) able to withstand 4 times the maximum load likely to be imposed; - (b) clean and free of grease, oil or other substances that may cause slipping; - (c) maintained in a safe condition; - (d) inspected at all of the following times by a competent person to ensure all components are in an adequate condition and the ladder is safe to use - (i) before each use, - (ii) annually; Clause 148(1)(d) replaced: O.I.C. 2013-65, N.S. Reg. 53/2013. - (e) not used, where the inspection required in clause (d) identifies an inadequate condition with the ladder. - (2 ) An employer shall ensure that a person using a fixed or portable ladder shall - (a) face the ladder when climbing or descending; - (b) when more than 1 m above a safe surface, maintain adequate contact with the \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_

[3] Occupational Safety General Regulations (N.S. Reg. 44/99)

Page 80

Open source document

Source excerpt

- (b) is equipped with a non-slip surface or cleats; - (c) where the ramp is greater than 1.8 m in rise, has a guardrail and supporting structure on any open side; Clause 145(1)(c) amended: O.I.C. 2000-130, N.S. Reg. 52/2000. - (d) where planks are used, has planks securely fastened together; - (e) has a minimum width of 450 mm; and - (f) is able to withstand 4 times the maximum load likely to be imposed on the ramp. - (2) An employer shall ensure that a guardrail referred to in clause (1)(c) is constructed in accordance with the requirements for a guardrail in subsection 142(4). Subsection 145(2) amended: O.I.C. 2000-130, N.S. Reg. 52/2000. Subsection 145(3) repealed: O.I.C. 2000-130, N.S. Reg. 52/2000. ## Catwalks - In this Section, 'catwalk' means a walkway that is 1.8 m or more above the ground - 146 (1) or floor level. - (2) An employer shall ensure that a catwalk - (a) meets or exceeds the requirements of subsection (4); or Clause 146(2)(a) amended: O.I.C. 2013-65, N.S. Reg. 53/2013. - (b) is certified by an engineer as having been constructed in accordance with the certified design of an engineer. - (3) Where there is a reasonable doubt as to whether a catwalk is adequate, an employer shall ensure that - (a) an engineer provides a written assessment of the permanent catwalk; and - (b) where the assessment of the engineer required by clause (a) identifies an inadequacy, - (i) the catwalk is removed, or - (ii) modifications are made and are certified by an engineer as having been \_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_

[4] Safety Standards for General Safety and Health Standards (Chaper 296-24 WAC)

Page 351

Open source document

Source excerpt

\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_ Ship stair (ship ladder) . A stairway that is equipped with treads, stair rails, and open risers, and has a slope that is between 50 and 70 degrees from the horizontal. Spiral stairs . A series of treads attached to a vertical pole in a winding fashion, usually within a cylindrical space. Stair platform . An extended step or landing breaking a continuous run of stairs. Stair rail or stair rail system . A barrier erected along the exposed or open side of stairways to prevent employees from falling to a lower level. Stairway (stairs) . Risers and treads that connect one level with another, and includes any landings and platforms in between those levels. Stairways include standard, spiral, alternating tread-type, and ship stairs. Standard stairs . A fixed or permanently installed stairway. Ship, spiral, and alternating treadtype stairs are not considered standard stairs. Tread . A horizontal member of a stair or stairway, but does not include landings or platforms. Unprotected sides and edges . Mean any side or edge of a walking-working surface (except at entrances and other points of access) where there is no wall, guardrail system, or stair rail system to protect an employee from falling to a lower level. For requirements relating to unprotected sides and edges, see the unified fall protection rule (chapter 296-880 WAC). Walking-working surface . Any surface, whether horizontal or vertical on which an employee walks, works, or gains access to a work area or workplace location. Walking-working surfaces include, but are not limited to, floors, the ground, roofs, ramps, bridges, runways, stairs, dockboards, formwork and concrete reinforcing steel. [Statutory Authority: RCW 49.17.010, .040, .050, and .060. 20-12-091 (Order 19-05) § 296-24-[r…

[5] CAT 325F L Excavator Operation and Maintenance Manual

Page 72

Open source document

Source excerpt

- · Operation and Maintenance Manual, 'Quick Coupler - Lubricate' - · Operation and Maintenance Manual, 'Seat Belt Inspect' - · Operation and Maintenance Manual, 'Track Adjustment - Inspect' - · Operation and Maintenance Manual, 'Track Adjustment - Adjust' - · Operation and Maintenance Manual, 'Travel Alarm - Test' - · Operation and Maintenance Manual, 'Undercarriage - Check' Refer to the Maintenance Section for the detailed procedures. Refer to the Maintenance Interval Schedule for a complete list of scheduled maintenance. Note: Watch closely for leaks. If you observe a leak, find the source of the leak and correct the leak. If you suspect a leak or you observe a leak, check the fluid levels more frequently. Illustration 85  Inspect the attachment control linkage, attachment cylinders, and attachment for damage or excessive wear. Make any necessary repairs. Inspect the lights for broken bulbs and for broken lenses. Replace any broken bulbs and any broken lenses. Inspect the engine compartment for any trash buildup. Remove any trash buildup from the engine compartment. Inspect the cooling system for any leaks, for faulty hoses and for any trash buildup. Correct any leaks. Remove any trash from the radiator. Inspect all of the belts for the engine attachments. Replace any belts that are worn, frayed, or broken.  Illustration 86 g03887252 Inspect the hydraulic system for leaks. Inspect the tank, cylinder rod seals, hoses, tubes, plugs, connections, and fittings. Correct any leaks in the hydraulic system. Inspect the final drives for leaks. Make any necessary repairs. Inspect the swing drive for leaks. Make sure that all covers and guards are securely attached. Inspect the covers and the guards for damage.  Illustration 87 Inspect the steps, the walkways, and the handholds. Clean the steps, the walkways, and the handholds. Make any necessary repairs. Inspect the operator compartment for trash buildup. Check …

[6] Rules for the Administration of the Oregon Safe Employment Act (General Occupational Safety and Health, Division 2, OSHA Oregon)

Page 1690

Open source document

Source excerpt

Oregon Occupational Safety and Health Division - (iv) Nonslip floors. Floors, footwalks, and passageways in the work area around machines or other places where a person is required to stand or walk shall be provided with effective means to minimize slipping. - (4) Walkways, docks, and platforms. - (i) Width. Walkways, docks, and platforms shall be of sufficient width to provide adequate passage and working areas. - (ii) Maintenance. Walkways shall be evenly floored and kept in good repair. - (iii) Docks. Docks and runways used for the operation of lift trucks and other vehicles shall have a substantial guard or shear timber except where loading and unloading are being performed. - (iv) Elevated walks. All elevated walks, runways, or platforms, if 4 feet or more from the floor level, shall be provided with a standard railing except on loading or unloading sides of platforms. If height exceeds 6 feet, a standard toeboard also shall be provided to prevent material from rolling or falling off. - (v) Elevated platforms. Where elevated platforms are used routinely on a daily basis they shall be equipped with stairways or fixed ladders that comply with Subpart D of this part. - (vi) Hazardous locations. Where required, walkways and stairways with standard handrails shall be provided in elevated and hazardous locations. Where such passageways are over walkways or work areas, standard toeboards shall be provided. - (5) Stairways. - (i) Construction. Stairways shall be constructed in accordance with Subpart D of this part. - (ii) Handrails. Stairways shall be provided with a standard handrail on at least one side or on any open side. Where stairs are more than 4 feet wide there shall be a standard handrail at each side, and where more than 8 feet wide, a third standard handrail shall be erected in the center of the stairway. - (iii) Lighting. All stairways shall be adequately lighted as prescribed in paragraph (c)(9) of this section. - (6) Emergency exits including doors and…

Publication receipt

Publisher: SALUS
Final reviewer: Francis Langlois
Original answer: May 28, 2025

Who, how, and why

Rosie, the contractors' AI Admin & Risk Assistant, works across the operational workflows to take care of the busy work, make capture in the field effortless, surface risk, and create business-ready outputs—without removing human judgment.

Rosie was grounded in a curated, human-created, SALUS-verified source library and retrieved relevant material for each question. SALUS published the English answer exactly as generated after duplicate screening. Francis Langlois reviewed the English content.

Rosie was offered as a free tool so people could ask real workplace-safety questions and receive immediate guidance. SALUS is preserving these human-requested answers because the same questions recur across jobsites and safety teams, and because the resulting threads can help people compare experience, clarify guidance and find relevant supporting material.

Topics

Safety compliance Equipment safety

This information supports professional judgment; it does not replace applicable requirements, site-specific procedures, or advice from a qualified person.

Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.

New contributions are temporarily closed while the moderation queue is configured.

Community answers(0)

No community answers have been approved yet.

Comments on Rosie's answer(0)

No comments have been approved yet.

Rosie's answer

Sources used for this answer

Keep exploring.

Aerial work

pressure testing

fire extinguisher size

what is the general industry standard regarding overhead cranes

Wrongful dismissal

Safety talk on High Risk training

Add your experience.

Community answers(0)

Comments on Rosie's answer(0)

Ready to put operational safety to work?