Welding gloves: choosing the right pair
Reviewed by Julie Gunn, Head of Services, SALUS Safety
The question, as asked: Welding gloves
A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.
Rosie's answer
Published by SALUSWhen selecting welding gloves, it's important to consider the specific hazards associated with welding tasks, such as exposure to heat, sparks, and potential cuts. Here are some key points to consider:
- Material and Flame Resistance: Welding gloves should be made from flame-resistant materials to protect against burns and sparks. Leather is a common choice due to its durability and resistance to heat and flames [1].
- Gauntlet Style: For most welding tasks, flameproof gauntlet gloves are recommended. These gloves extend over the wrist to provide additional protection from sparks and heat [1].
- Dexterity and Fit: While protection is crucial, the gloves should also allow for sufficient dexterity to handle welding tools effectively. It's important to balance protection with the ability to perform tasks without excessive restriction [2].
- Maintenance and Inspection: Regular inspection and maintenance of gloves are necessary to ensure they remain effective. Gloves should be checked for any damage, such as cuts or burns, and replaced if they no longer provide adequate protection [2].
- Specific Hazards: Consider any specific hazards related to the materials being welded, such as chemical exposure, and select gloves that provide appropriate protection against these risks [2].
By considering these factors, you can select welding gloves that provide the necessary protection while allowing for effective performance of welding tasks.
Sources used for this answer
[1] Rules for the Administration of the Oregon Safe Employment Act (General Occupational Safety and Health, Division 2, OSHA Oregon)
Page 881
Open source documentSource excerpt
Oregon Occupational Safety and Health Division Oregon Administrative Rules AO 2-2023 Division 2 It is also important to know the performance characteristics of gloves relative to the specific hazard anticipated; e.g., chemical hazards, cut hazards, flame hazards, etc. These performance characteristics should be assessed by using standard test procedures. Before purchasing gloves, the employer should request documentation from the manufacturer that the gloves meet the appropriate test standard(s) for the hazard(s) anticipated. Other factors to be considered for glove selection in general include: - (A) As long as the performance characteristics are acceptable, in certain circumstances, it may be more cost effective to regularly change cheaper gloves than to reuse more expensive types; and, - (B) The work activities of the employee should be studied to determine the degree of dexterity required, the duration, frequency, and degree of exposure of the hazard, and the physical stresses that will be applied. With respect to selection of gloves for protection against chemical hazards: - (A) The toxic properties of the chemical(s) must be determined; in particular, the ability of the chemical to cause local effects on the skin and/or to pass through the skin and cause systemic effects; - (B) Generally, any 'chemical resistant' glove can be used for dry powders; - (C) For mixtures and formulated products (unless specific test data are available), a glove should be selected on the basis of the chemical component with the shortest breakthrough time, since it is possible for solvents to carry active ingredients through polymeric materials; and, - (D) Employees must be able to remove the gloves in such a manner as to prevent skin contamination. - 12. Cleaning and maintenance. It is important that all PPE be kept clean and properly maintained. Cleaning is particularly important for eye and face protection where dirty or fogged lenses could impair vision. For the purposes…
[2] Safety Standards for General Safety and Health Standards (Chaper 296-24 WAC)
Page 338
Open source documentSource excerpt
\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_ - Note: In gas welding or oxygen cutting where the torch produces a high yellow light, is not desirable to use a filter or lens that absorbs the yellow or sodium line in the visible light of the operation. - (j) All filter lenses and plates must meet the test for transmission of radiant energy prescribed in ANSI Z 87.1-1968--American National Standard Practice for Occupational and Educational Eye and Face Protection. - (3) Protection from arc welding rays . Where the work permits, the welder should be enclosed in an individual booth painted with a finish of low-reflectivity such as zinc oxide (an important factor for absorbing ultraviolet radiations) and lamp black, or must be enclosed with noncombustible screens similarly painted. Booths and screens must permit circulation of air at floor level. You must protect workers or other persons adjacent to the welding areas from the rays by noncombustible or flameproof screens or shields or they must be required to wear appropriate goggles. [Statutory Authority: RCW 49.17.010, .040, .050, and .060. 15-24-100 (Order 15-04), § 296-24-[redacted postal code], filed 12/01/2015, effective 01/05/2016. Statutory Authority: RCW 49.17.010, .040, .050. 01-11-038 (Order 99-36), § 296-24-[redacted postal code], filed 05/09/01, effective 09/01/01. Statutory Authority: Order 73-5, 296-24-[redacted postal code], filed 5/9/73 and Order 73-4, 296-24-[redacted postal code], filed 5/7/73.] ## WAC 296-24-[redacted postal code] Protective clothing. - (1) General requirements . You must protect employees exposed to the hazards created by welding, cutting, or brazing operations by personal protective equipment in accordance with the requirements of chapter 296-24 WAC, Part I, and WAC [redacted identifier]. Appropriate prote…
Keep exploring.
pipeline hydrotest
Safe Work Procedure: Pipeline Hydrotest Document Number: [SWP-NUMBER] Revision Date: [DATE] Next Review Date: [NEXT REVIEW DATE] Department: [DEPARTMENT NAME] 1. Scope This procedure covers the safe execution of hydrostatic testing on pipelines to ensure their integrity and safety before being put into service. It
Read the thread