Write a toolbox talk on hot work

Source excerpt

169 (3) An employer must ensure that the tests referred to in subsection (2)(d) are repeated at regular intervals appropriate to the hazard associated with the work being performed. ## Hot taps 170 (1) An employer must develop procedures in a hot tap plan specific to the type or class of hot tap work being performed before hot tap work begins. - 170 (2) The employer must ensure that the plan includes - (a) a site hazard analysis, - (b) a description of the sequence of events, - (c) safety precautions to address the hazards, and - (d) an emergency response plan. - 170 (3) The employer must ensure that - (a) only competent workers are permitted to carry out a hot tap operation, - (b) the point in the pressure containing barrier to be hot tapped is checked and strong enough for the hot tap to be done safely, - (c) adequate working space is available at the location of the hot tap, - (d) exit routes are available and their locations known by workers involved in the work, - (e) workers wear appropriate personal protective equipment when a hot tap is performed on equipment containing hydrocarbons, combustible fluids, superheated steam or any other hazardous material, - (f) material being supplied to the equipment being hot tapped can be shut off immediately in an emergency, - (g) the hot tap machine and fittings are of adequate design and capability for the process, conditions, pressure and temperature, and - (h) the pressure in the equipment being hot tapped is as low as practical during the hot tap operation. 170 (4) An employer must ensure, where reasonably practicable, that a hot tap is not undertaken if at the proposed hot tap location - (a) the equipment contains a harmful substance, - (b) the equipment is in hydrogen service, or - (c) the equipment contains an explosive mixture. ## Spray operations 170.1 (1) An employer must ensure that a spray booth used to apply flammable substances is provided with ventilation in accordance with Part 26 and that the venti…

Source excerpt

## 4. Hot Work Permit The implementation of a permit system for hot work is intended to assure that employers maintain control over operations involving hot work and to assure that employees are aware of and utilize appropriate safeguards when conducting these activities. Precautions for hot work operations are specified in 29 CFR 1910.252(a), and include such safeguards as relocating the hot work operation to a safe location if possible, relocating or covering combustible material in the vicinity, providing fire extinguishers, and provisions for establishing a fire watch. Permits are not required for hot work operations conducted in the presence of the employer or the employer's authorized representative who would otherwise issue the permit, or in an employer authorized welding shop or when work is conducted outside and away from the facility. It should be noted that the permit is not a record, but is an authorization of the employer certifying that certain safety precautions have been implemented prior to the beginning of work operations. ## 5. Entry Into Bins, Silos, and Tanks In order to assure that employers maintain control over employee entry into bins, silos, and tanks, OSHA is requiring that the employer issue a permit for entry into bins, silos, and tanks unless the employer (or the employer's representative who would otherwise authorize the permit) is present at the entry and during the entire operation. Employees should have a thorough understanding of the hazards associated with entry into bins, silos, and tanks. Employees are not to be permitted to enter these spaces from the bottom when grain or other agricultural products are hung up or sticking to the sides which might fall and injure or kill an employee. Employees should be made aware that the atmosphere in bins, silos, and tanks can be oxygen deficient or toxic. Employees should be trained in the proper methods of testing the atmosphere, as well as in the appropriate procedures to be take…

Source excerpt

- (i) operate below the temperature that would ignite a flammable substance present in the hazardous location, or - (ii) are shielded or blanketed in such a way as to prevent a flammable substance in the hazardous location from contacting the surface, ## and - (c) the combustion air intake and exhaust discharge are equipped with a flame arresting device or are located outside the hazardous location. 168 (6) If it is not reasonably practicable to comply with subsection (5)(b), an employer must ensure that another effective safeguard is established. ## Hot work 169 (1) Despite any other section in this Part, an employer must ensure that hot work is done in accordance with subsections (2) and (3) if - (a) the work area is a hazardous location, or - (b) the work area is not normally a hazardous location but an explosive atmosphere may exist for a limited time because - (i) a flammable substance is or may be in the atmosphere of the work area, - (ii) a flammable substance is or may be stored, handled, processed or used in the location, - (iii) the hot work is on or in an installation or item of equipment that contains a flammable substance or its residue, or - (iv) the hot work is on a vessel that contains residue that may release a flammable gas or vapour when exposed to heat. - 169 (2) An employer must ensure that hot work is not begun until - (a) a hot work permit is issued that indicates - (i) the nature of the hazard, - (ii) the type and frequency of atmospheric testing required, - (iii) the safe work procedures and precautionary measures to be taken, and - (iv) the protective equipment required, - (b) the hot work location is - (i) cleared of combustible materials, or - (ii) suitably isolated from combustible materials, - (c) procedures are implemented to ensure continuous safe performance of the hot work, and - (d) testing shows that the atmosphere does not contain - (i) a flammable substance, in a mixture with air, in an amount exceeding 20 percent of that …

Source excerpt

\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_\_ - Note: In gas welding or oxygen cutting where the torch produces a high yellow light, is not desirable to use a filter or lens that absorbs the yellow or sodium line in the visible light of the operation. - (j) All filter lenses and plates must meet the test for transmission of radiant energy prescribed in ANSI Z 87.1-1968--American National Standard Practice for Occupational and Educational Eye and Face Protection. - (3) Protection from arc welding rays . Where the work permits, the welder should be enclosed in an individual booth painted with a finish of low-reflectivity such as zinc oxide (an important factor for absorbing ultraviolet radiations) and lamp black, or must be enclosed with noncombustible screens similarly painted. Booths and screens must permit circulation of air at floor level. You must protect workers or other persons adjacent to the welding areas from the rays by noncombustible or flameproof screens or shields or they must be required to wear appropriate goggles. [Statutory Authority: RCW 49.17.010, .040, .050, and .060. 15-24-100 (Order 15-04), § 296-24-[redacted postal code], filed 12/01/2015, effective 01/05/2016. Statutory Authority: RCW 49.17.010, .040, .050. 01-11-038 (Order 99-36), § 296-24-[redacted postal code], filed 05/09/01, effective 09/01/01. Statutory Authority: Order 73-5, 296-24-[redacted postal code], filed 5/9/73 and Order 73-4, 296-24-[redacted postal code], filed 5/7/73.] ## WAC 296-24-[redacted postal code] Protective clothing. - (1) General requirements . You must protect employees exposed to the hazards created by welding, cutting, or brazing operations by personal protective equipment in accordance with the requirements of chapter 296-24 WAC, Part I, and WAC [redacted identifier]. Appropriate prote…

Source excerpt

Oregon Administrative Rules Oregon Occupational Safety and Health Division ## FIRE PREVENTION J ## §1926.352 Fire Prevention. - (a) When practical, objects to be welded, cut, or heated shall be moved to a designated safe location or, if the objects to be welded, cut, or heated cannot be readily moved, all movable fire hazards in the vicinity shall be taken to a safe place, or otherwise protected. - (b) If the object to be welded, cut, or heated cannot be moved and if all the fire hazards cannot be removed, positive means shall be taken to confine the heat, sparks, and slag, and to protect the immovable fire hazards from them. - (c) No welding, cutting, or heating shall be done where the application of flammable paints, or the presence of other flammable compounds, or heavy dust concentrations creates a hazard. - (d) Suitable fire extinguishing equipment shall be immediately available in the work area and shall be maintained in a state of readiness for instant use. - (e) When the welding, cutting, or heating operation is such that normal fire prevention precautions are not sufficient, additional personnel shall be assigned to guard against fire while the actual welding, cutting, or heating operation is being performed, and for a sufficient period of time after completion of the work to ensure that no possibility of fire exists. Such personnel shall be instructed as to the specific anticipated fire hazards and how the firefighting equipment provided is to be used. - (f) When welding, cutting, or heating is performed on walls, floors, and ceilings, since direct penetration of sparks or heat transfer may introduce a fire hazard to an adjacent area, the same precautions shall be taken on the opposite side as are taken on the side on which the welding is being performed. - (g) For the elimination of possible fire in enclosed spaces as a result of gas escaping through leaking or improperly closed torch valves, the gas supply to the torch shall be positively shut off…

Source excerpt

## OCCUPATIONAL HEALTH AND SAFETY, 2020 ## Flammable or explosive substance in atmosphere - 25-11 (1) If a flammable or explosive substance is present in the atmosphere of a worksite at a level that is more than 20% of the lower explosive limit of that substance, an employer or contractor shall not require or permit a worker to enter or work at the worksite. - (2) Subsection (1) does not apply to: - (a) a firefighter who has been trained pursuant to section 32-4; or - (b) a competent worker who meets the requirements of subsection (3) and who is acting in an emergency situation at the place of employment. - (3) An employer shall ensure that: - (a) the competent worker mentioned in clause (2) (b) is trained, equipped and works according to an approved standard; - (b) the training required by clause (a) is provided by a competent person; and - (c) a written record is kept of all training delivered to a worker pursuant to clause (a). 31 Dec 2020 c S-15.1 Reg 10 s25-11. ## Hot work - 25-12 (1) If a flammable substance is or may be present, an employer or contractor shall ensure that no hot work is performed until: - (a) suitable tests have been conducted that: - (i) indicate whether the atmosphere contains a flammable substance in a quantity sufficient to create an explosive atmosphere; and - (ii) confirm that the work may be safely performed; and - (b) the work procedures developed pursuant to clause 25-5(1) (b) have been implemented to ensure continuous safe performance of the work. - (2) While hot work is being performed, an employer or contractor shall conduct tests described in clause (1) (a) at intervals appropriate to the work being performed and record the results. - (3) An employer or contractor shall not require or permit any hot work to be performed in the vicinity of a material that may constitute a fire hazard until suitable steps have been taken to reduce the risk of fire. - (4) An employer or contractor shall ensure that a container or piping that…