Observation teaching
A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.
Rosie's answer
Published by SALUSIt is always the operator's responsibility to use the machine in a safe and proper manner. Only trained operators should be allowed to control the machine. Under no circumstance should this machine be used in such a manner as to contravene any international, national or local health and safety at work regulations, or factories acts and subordinate regulations. [1]
Sources used for this answer
[1] Simon Electric Eagle 32/21N and 41/24N (PN 89-412792) - Operator's Manual
Page 24
Open source documentSource excerpt
# SECTION 2 # SAFE WORKING PRACTICE 1. USE OF THE MACHINE: (a) AT ALL TIMES, IT IS THE RESPONSIBILITY OF THE OPERATOR TO USE THE MACHINE IN A SAFE AND PROPER MANNER. (b) ONLY TRAINED OPERATORS SHOULD BE ALLOWED TO CONTROL THE MACHINE. (c) UNDER NO CIRCUMSTANCE SHOULD THIS MACHINE BE USED IN SUCH A MANNER AS TO CONTRAVENE ANY INTERNATIONAL, NATIONAL OR LOCAL HEALTH AND SAFETY AT WORK REGULATIONS, OR FACTORIES ACTS AND SUBORDINATE REGULATIONS. 2. INFORMATION SOURCES: - THE FOLLOWING INFORMATION SHOULD BE READ AND UNDERSTOOD: (a) "Mobile Elevating Work Platforms", Draft European Standard, Document No.88/[redacted postal code]., by British Standards Institute, 1988. (b) "Specification for Mobile Elevating Work Platforms", Document B.S. 7171., by British Standard Institute, 1989. (c) "Safety in Work with Powered Operated Mobile Work Platforms". Health and Safety Guidance Note HS(G) 19., by H.M.S.O. (d) "Avoidance of Danger from Overhead Electric Lines". Health and Safety Guidance Note GS6., by H.M.S.O. (e) "I.P.A.F. Guide to MEWPs (Mobile Elevating Work Platforms)", by the International Powered Access Federation, 1987. 3. HAZARDS: - ONLY TRAINED MEDICALLY FIT OPERATORS SHOULD OPERATE THE MACHINE. IF UNTRAINED PERSONS ARE PRESENT IN THE PLATFORM FOR INSPECTION DUTIES THEY SHOULD NOT BE PERMITTED TO CONTROL THE MACHINE. - The following instructions are minimum requirements to be adapted for safe working practice with the Boxer Mk.3 machine: (a) The safe working load of 225 kgs (496 lbs) must not be exceeded (two persons only), unless specified otherwise in Chart 4 (Section 1 - Specification). (b) The machine must not be elevated on ground that is more than 5.0 degrees out of level. The ground must be well compacted and capable of taking the weight transferred to the wheels in all stages of operation. In general, a road quality surface is required. (c) The machine must not be used in wind speeds in excess of 10 metres per seco…
Keep exploring.
Oil and gas industry water transfer water truck safety with jsa compliance
Toolbox Talk: Water Truck Safety in Oil and Gas Industry *Date:** [DATE] *Duration:** [DURATION] minutes *Presenter:** [PRESENTER NAME] *Location:** [LOCATION] Objective To ensure all personnel understand the safety protocols and Job Safety Analysis (JSA) compliance requirements when operating water trucks for water
Read the threadData center toolbox topic
Data Center Toolbox Use ======================= Document Number: \[SWP-NUMBER] Revision Date: \[DATE] Next Review Date: \[NEXT REVIEW DATE] Department: \[DEPARTMENT NAME] 1\. Scope This Safe Work Procedure (SWP) outlines the safety guidelines and regulatory compliance requirements for the use of toolboxes within data
Read the threadPerform a risk assessment for excavation work
Risk Assessment for Excavation Work 1. Hazard Identification Cave-ins: The most significant hazard in excavation work is the risk of cave-ins, which can occur if the sides of the excavation are not properly supported or sloped [1]. Falling Objects: Loose soil or rocks can fall into the excavation, posing a risk to
Read the threadCreate a site orientation that meet compliance to BC, Canada
For construction or industrial worksites in British Columbia, site orientation and worker onboarding should be treated as a mandatory, documented, site-specific process under the Workers Compensation Act framework and the Occupational Health and Safety Regulation. At minimum, every young or new worker must receive
Read the threadHazcom
Safe Work Procedure: Hazard Communication (HazCom) Document Number: [SWP-NUMBER] Revision Date: [DATE] Next Review Date: [NEXT REVIEW DATE] Department: [DEPARTMENT NAME] 1. Scope This Safe Work Procedure (SWP) outlines the requirements for hazard communication, ensuring that all employees are informed about the
Read the threadWhat should a HSE Manager inspect when visiting a customer site?
As a HSE Manager visiting a customer site in Texas, you should inspect various aspects to ensure safety and health compliance. Here's a breakdown of key areas to consider: Compliance Audits: 1, 5, 9 Conduct a thorough audit of the customer's safety management system 1, 5. This includes evaluating the design and
Read the threadAdd your experience.
Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.
New contributions are temporarily closed while the moderation queue is configured.
Community answers(0)
No community answers have been approved yet.
Comments on Rosie's answer(0)
No comments have been approved yet.