Asked by a personGeneral — US and Canadaen-CA

Using a hammer wrench

A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.

Rosie's answer

Published by SALUS

When working on or near machinery, it is important to use personal protective equipment (PPE) to protect your eyes, ears, hands, feet, and body. [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20]

I was unable to find information about hammer wrench safety procedures in the provided documents. Here is some general safety guidance based on industry standards and best practices:

PPE: Safety glasses, gloves, and appropriate work boots are recommended when using a hammer wrench.
Inspection: Before use, inspect the hammer wrench for any signs of damage, such as cracks, wear, or loose parts. Do not use if damaged.
Correct Size: Use the correct size hammer wrench for the nut or bolt. A loose fit can cause slippage and injury.
Striking Surface: Ensure the striking surface of the wrench is clean and free from oil or debris to prevent glancing blows.
Proper Stance: Maintain a balanced stance and keep your eyes on the striking surface.
Controlled Strikes: Use controlled and deliberate strikes. Avoid excessive force.
No Modifications: Never modify a hammer wrench.
Avoid Overextension: Do not use pipes or other extensions to increase leverage, as this can cause the tool to break or the fastener to fail.
Storage: Store hammer wrenches in a dry, secure place to prevent damage and corrosion.

20 source record(s)

Sources used for this answer

[1] Articulating Booms - SJ45 AJ+, SJ60 AJ+ (238264) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. ## WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10 ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>â 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe dis…

[2] DC Electric Scissors (239872) - Operation Manual

Page 13

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged, or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10 ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>â 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distanc…

[3] Rough Terrain Scissors - SJ6826 RT, SJ6832 RT (221587) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) to protect your eyes, ears, hands, feet, and body when you do work on or near machinery. Any modifications to the MEWP must have written permission from Skyjack. WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distance …

[4] DC Electric Scissors - SJ3215 E, SJ3219 E, SJ3226 E, SJ4732 E, SJ4740 E (248537) - Operation Manual

Page 13

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) to protect your eyes, ears, hands, feet, and body when you do work on or near machinery. Any modifications to the MEWP must have written permission from Skyjack. WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection if it is near or in contact with energized electrical conductors. Refer to Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculations. If you need to work nearer than 3 m (10 ft), stop and apply control measures for electrical transmission and distribution as determined by a qualified person. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>â 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures for electrical transmission and distribution as determined by a qualified person.</td></tr></table> DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, and tools a safe distance away from power lines, ele…

[5] Telescopic Booms - SJ82 T, SJ86 T (213205) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions A WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. A WARNING Do not operate the MEWP if: ■ - It does not operate correctly ■ It is damaged or shows worn or missing parts ■ The safety devices are tampered with or disabled ■ It is locked and tagged for servicing or repair ■ It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10 ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> A DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe dis…

[6] DC Electric Scissors - SJ3215, SJ3219, SJ3220, SJ3226, SJ4726, SJ4732, SJ4740 (216380) - Operation Manual

Page 13

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged, or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3m (10ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distance away …

[7] DC Electric Scissors - SJ3213 micro, SJ3219 micro (248548) - Operation Manual

Page 13

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) to protect your eyes, ears, hands, feet, and body when you do work on or near machinery. Any modifications to the MEWP must have written permission from Skyjack. WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged, or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10 ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distanc…

[8] Rough Terrain Scissors - SJ9233 RT, SJ9243 RT, SJ9253 RT, SJ9664 RT (221491) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. ## WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe dist…

[9] Telescopic Booms - SJ40 T+, SJ45 T+ (238261) - Operation Manual

Page 15

Open source document

Source excerpt

[10] Vertical Mast SJ12 E, SJ16 E, SJ20 E (243452) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions A WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) to protect your eyes, ears, hands, feet, and body when you do work on or near machinery. Any modifications to the MEWP must have written permission from Skyjack. A WARNING Do not operate the MEWP if: ■ It does not operate correctly. ■ It is damaged or shows worn or missing parts. ■ The safety devices are tampered with or disabled. ■ It is locked and tagged for servicing or repair. ■ It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection if it is near or in contact with energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider the MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10 ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> A DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, and tools a safe dis…

[11] Articulating Booms Hybrid - SJ45 AJHE+, SJ60 AJHE+ (251710) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. ## WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>â 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distance away from power lines, electrical power sources, or energized sources. If you do not obey, there is a risk of death or serious injury. Keep a minimum safe distance from…

[12] Telescopic Booms - SJ40 T+, SJ45 T+, SJ61 T+, SJ66 T+ (213201) - Operation Manual

Page 17

Open source document

Source excerpt

[13] DC Electric Scissors - SJ3215 E, SJ3219 E, SJ3220 E, SJ3226 E, SJ4726 E, SJ4732 E, SJ4740 E (249533) - Operation Manual

Page 13

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) to protect your eyes, ears, hands, feet, and body when you do work on or near machinery. Any modifications to the MEWP must have written permission from Skyjack. WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection if it is near or in contact with energized electrical conductors. Refer to Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculations. If you need to work nearer than 3 m (10 ft), stop and apply control measures for electrical transmission and distribution as determined by a qualified person. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>â 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures for electrical transmission and distribution as determined by a qualified person.</td></tr></table> DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, and tools a safe distance away from power lines, ele…

[14] Vertical Mast SJ12, SJ16 (213721) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions A WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. A WARNING Do not operate the MEWP if: ■ It does not operate correctly ■ It is damaged, or shows worn or missing parts ■ The safety devices are tampered with or disabled ■ It is locked and tagged for servicing or repair ■ It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3m (10ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distan…

[15] Articulating Booms - SJ46 AJ+ (213208) - Operation Manual

Page 15

Open source document

Source excerpt

[16] Rough Terrain Scissors - SJ6826 RT, SJ6832 RT (257020) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) to protect your eyes, ears, hands, feet, and body when you do work on or near machinery. Any modifications to the MEWP must have written permission from Skyjack. A WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged or shows worn or missing parts - The safety devices are tampered with or disabled ■ It is locked and tagged for servicing or repair ■ It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> A DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distance…

[17] Articulating Booms - SJ63 AJ+ (213211) - Operation Manual

Page 15

Open source document

Source excerpt

[18] Vertical Mast SJ12 E, SJ16 E, SJ20 E (243762) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) to protect your eyes, ears, hands, feet, and body when you do work on or near machinery. Any modifications to the MEWP must have written permission from Skyjack. WARNING Do not operate the MEWP if: - It does not operate correctly. - It is damaged or shows worn or missing parts. - The safety devices are tampered with or disabled. - It is locked and tagged for servicing or repair. - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection if it is near or in contact with energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider the MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10 ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, and tools a safe d…

[19] Articulating Booms - SJ45 AJE+, SJ60 AJE+ (251711) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury, or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. ## WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. Obey all the national, state/provincial/territorial and local safety rules. 2.1-1 Minimum distance from electrical conductor <table><tr><th>Volge Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distance away from power lines, electrical power sources, or energized sources. If you do not obey, there is a risk of death or serious injury. Keep a minimum safe distance from …

[20] Vertical Mast SJ20 (236504) - Operation Manual

Page 15

Open source document

Source excerpt

# Section 2 - General Safety Precautions WARNING Failure to obey the instructions and precautions in this manual could result in MEWP damage, property damage, personal injury or death. It is mandatory that you use this MEWP correctly. Read this manual and make sure you fully understand it before you operate the MEWP. Use personal protective equipment (PPE) when you do work on or near machinery to protect your eyes, ears, hands, feet, and body. Any modifications to the MEWP must have written permission from Skyjack. WARNING Do not operate the MEWP if: - It does not operate correctly - It is damaged, or shows worn or missing parts - The safety devices are tampered with or disabled - It is locked and tagged for servicing or repair - It was modified without permission from Skyjack and the MEWP owner. If you do not obey, there is a risk of death or serious injury. ## 2.1 Electrocution hazards The MEWP is not electrically insulated and does not provide protection from contact with or proximity to energized electrical conductors. Follow Section 2.1-1 for the minimum distance to keep between all parts of the MEWP, occupants, or tools, and the electrical conductors. Consider MEWP movement and electrical line sway in minimum distance calculation. If you need to work nearer than 3 m (10 ft), stop and apply control measures as determined by a qualified person with respect to electrical transmission and distribution. Obey all the national, state/provincial/territorial and local safety rules. ## 2.1-1 Minimum distance from electrical conductors <table><tr><th>Voltage Range</th><th>Minimum Distance from Electrical Conductors</th></tr><tr><td>≤ 50 KVA</td><td>3 m (10 ft)</td></tr><tr><td>> 50 KVA, or if not known</td><td>STOP and apply control measures as determined by a qualified person with respect to electrical transmission and distribution.</td></tr></table> ## DANGER Electrocution hazard. Keep all parts of the MEWP, occupants, or tools a safe distance…

Publication receipt

Publisher: SALUS
Final reviewer: Francis Langlois
Original answer: Sep 5, 2025

Who, how, and why

Rosie, the contractors' AI Admin & Risk Assistant, works across the operational workflows to take care of the busy work, make capture in the field effortless, surface risk, and create business-ready outputs—without removing human judgment.

Rosie was grounded in a curated, human-created, SALUS-verified source library and retrieved relevant material for each question. SALUS published the English answer exactly as generated after duplicate screening. Francis Langlois reviewed the English content.

Rosie was offered as a free tool so people could ask real workplace-safety questions and receive immediate guidance. SALUS is preserving these human-requested answers because the same questions recur across jobsites and safety teams, and because the resulting threads can help people compare experience, clarify guidance and find relevant supporting material.

Topics

Equipment safety Incident management Personal protective equipment

This information supports professional judgment; it does not replace applicable requirements, site-specific procedures, or advice from a qualified person.

Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.

New contributions are temporarily closed while the moderation queue is configured.

Community answers(0)

No community answers have been approved yet.

Comments on Rosie's answer(0)

No comments have been approved yet.

Rosie's answer

Sources used for this answer

Keep exploring.

Saw safety

Clothing and safety

Loading and unloading lorry with for truck on nearside only. If not use the hiab crane

tool box talk

Angle Grinder

Cutoff,saw

Add your experience.

Community answers(0)

Comments on Rosie's answer(0)

Ready to put operational safety to work?