I need forms for tractors

Source excerpt

## FOREWORD <!-- image --> ## AVOID INJURY Read, understand and follow all safety precautions and procedures found in this manual before attempting any operation, inspection or maintenance of this machine, attachment or systems. Manufacturer cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are therefore not all inclusive. If a tool, procedure, work method or operating technique not specifically recommended by manufacturer is used, you must satisfy yourself that it is safe for you and others. You should also ensure that the product will not be damaged or made unsafe by the operation, lubrication, maintenance and/or repair procedures you choose. ## GENERAL - ・ This manual contains procedures to aid the operator gain peak performance through effective, economical operation and maintenance of the machine. - ・ Before operating the machine, operators must thoroughly read and understand all Safety, Operation and Maintenance instructions found in this manual. Failure to follow the instructions given in this manual may lead to serious injury to persons and or equipment failure. - ・ Operators and persons working with this machine should continually study this manual until proper Safety, Operation and Maintenance procedures are completely understood. - ・ This manual describes the basic operating techniques. Skill is gained as the operator utilizes these techniques and perfects them with an actual machine. - ・ Some illustrated pictures may be different from your machine, as technical improvement is continuous, manuals are periodically updated to reflect these changes. - ・ This manual may not contain attachments and optional equipment that are available in your area. Please contact an authorized Manufacturer Distributor for any optional attachments required. - ・ The contents of this manual and operation of the machine are based on the use of genuine manufacturer sourced parts. Use of non…

Source excerpt

S-15.1 REG 10 ## OCCUPATIONAL HEALTH AND SAFETY, 2020 ## Visual inspection - 11-3 (1) Before a worker starts any powered mobile equipment, an employer or contractor shall ensure that the worker makes a complete visual inspection of the equipment and the surrounding area to ensure that no worker, including the operator, is endangered by the start-up of the equipment. - (2) No worker shall start any powered mobile equipment until the inspection required by subsection (1) is completed. 31 Dec 2020 c S-15.1 Reg 10 s11-3. ## Inspection and maintenance - 11-4 An employer or contractor shall ensure that: - (a) all powered mobile equipment is inspected by a competent person for defects and unsafe conditions as often as is necessary to ensure that it is capable of safe operation; - (b) if a defect or unsafe condition that may create a hazard to a worker is identified in the powered mobile equipment: - (i) steps are taken immediately to protect the health and safety of any worker who may be at risk until the defect is repaired or the unsafe condition is corrected; and - (ii) as soon as is reasonably practicable, the defect is repaired or the unsafe condition is corrected; and - (c) a written record of the inspections and maintenance carried out pursuant to clauses (a) and (b) is kept at the place of employment and made readily available to the operator. 31 Dec 2020 c S-15.1 Reg 10 s11-4. ## Requirements for powered mobile equipment - 11-5 (1) An employer, contractor or supplier shall ensure that each unit of powered mobile equipment is equipped with: - (a) a device within easy reach of the operator that will permit the operator to stop as quickly as possible any ancillary equipment driven from the powered mobile equipment, including any power take-off, crane and auger and any digging, lifting and cutting equipment; - (b) a horn or other audible warning device; - (c) seats that are designed and installed to ensure the safety of all wor…

Source excerpt

level of safety is used; - (b) a manually operated horn, unless such a horn was not installed at the time of manufacture; - (c) adequate front and rear lights when the equipment is used after dark or in dimly lit areas; - (d) an adequate braking system; and - (e) a screen, shield, grill, deflector, guard or other adequate protection for the operator, where the operator may be exposed to the hazard of flying or intruding objects. Subsection 58(1) renumbered Section 58 and amended: O.I.C. 2000-130, N.S. Reg. 52/2000; amended: O.I.C. 2013-65, N.S. Reg. 53/2013. - 59 An employer shall ensure that a hoist or powered mobile equipment that is equipped with outriggers or stabilizers is operated with the outriggers or stabilizers engaged, unless the manufacturer's specifications permit otherwise. Section 59 replaced: O.I.C. 2000-130, N.S. Reg. 52/2000. - 60 An employer shall ensure that a hoist, lift truck or powered mobile equipment is not altered in such a way as to render ineffective a safety device or control, except where the change has been certified in writing by the manufacturer or an engineer to afford protection equal to or greater than the protection afforded by the original safety device or control. Section 60 amended: O.I.C. 2013-65, N.S. Reg. 53/2013. - 61 An employer shall take adequate precautions to ensure that a hoist, lift truck or powered mobile equipment does not tip or roll over. Section 61 amended: O.I.C. 2013-65, N.S. Reg. 53/2013. ## Overhead protection 62 - (1) Where an employee who is an operator of powered mobile equipment is exposed to a hazard from falling objects, an employer shall ensure that the powered mobile equipment is equipped with a protective structure adequate for the conditions in which the equipment is being used and that meets the requirements of the latest version of the applicable standard listed below or that is certified by an engineer or the manufacturer to provide equivalent or better protection: - (a) SAE standard…