What is the fall protection trigger height for residential framers in California?

Source excerpt

## 29 CFR 1926 (OSHA) Toeboard means a low protective barrier that will prevent the fall of materials and equipment to lower levels and provide protection from falls for personnel. Unprotected sides and edges means any side or edge (except at entrances to points of access) of a walking/working surface, e.g., floor, roof, ramp, or runway where there is no wall or guardrail system at least 39 inches (1.0 m) high. Walking/working surface means any surface, whether horizontal or vertical on which an employee walks or works, including, but not limited to, floors, roofs, ramps, bridges, runways, formwork and concrete reinforcing steel but not including ladders, vehicles, or trailers, on which employees must be located in order to perform their job duties. Warning line system means a barrier erected on a roof to warn employees that they are approaching an unprotected roof side or edge, and which designates an area in which roofing work may take place without the use of guardrail, body belt, or safety net systems to protect employees in the area. Work area means that portion of a walking/working surface where job duties are being performed. [59 FR [redacted postal code], Aug. 9, 1994, as amended at 60 FR [redacted postal code], Aug. 2, 1995; 66 FR 5265, Jan. 18, 2001; 75 FR [redacted postal code], Aug. 9, 2010; 79 FR [redacted postal code], Apr. 11, 2014] ## §1926.501 Duty to have fall protection. - (a) General. (1) This section sets forth requirements for employers to provide fall protection systems. All fall protection required by this section shall conform to the criteria set forth in §1926.502 of this subpart. - (2) The employer shall determine if the walking/working surfaces on which its employees are to work have the strength and structural integrity to support employees safely. Employees shall be allowed to work on those surfaces only when the surfaces have the requisite strength and structural integrity. - (b)(1) Unprotected sides and edges. Each employee …

Source excerpt

## 29 CFR 1926 (OSHA) - (ii) Each employee reaching more than 10 inches (25 cm) below the level of the walking/working surface on which they are working, shall be protected from falling by a guardrail system, safety net system, or personal fall arrest system. NOTE: Bricklaying operations performed on scaffolds are regulated by subpart L-Scaffolds of this part. - (10) Roofing work on Low-slope roofs. Except as otherwise provided in paragraph (b) of this section, each employee engaged in roofing activities on low-slope roofs, with unprotected sides and edges 6 feet (1.8 m) or more above lower levels shall be protected from falling by guardrail systems, safety net systems, personal fall arrest systems, or a combination of warning line system and guardrail system, warning line system and safety net system, or warning line system and personal fall arrest system, or warning line system and safety monitoring system. Or, on roofs 50-feet (15.25 m) or less in width (see appendix A to subpart M of this part), the use of a safety monitoring system alone [i.e. without the warning line system] is permitted. - (11) Steep roofs. Each employee on a steep roof with unprotected sides and edges 6 feet (1.8 m) or more above lower levels shall be protected from falling by guardrail systems with toeboards, safety net systems, or personal fall arrest systems. - (12) Precast concrete erection. Each employee engaged in the erection of precast concrete members (including, but not limited to the erection of wall panels, columns, beams, and floor and roof 'tees') and related operations such as grouting of precast concrete members, who is 6 feet (1.8 m) or more above lower levels shall be protected from falling by guardrail systems, safety net systems, or personal fall arrest systems, unless another provision in paragraph (b) of this section provides for an alternative fall protection measure. Exception: When the employer can demonstrate that it is infeasible or creates a greater hazard to u…

Source excerpt

- C.F.R. 1926 Subpart R Appendix G). (D) Custody of fall protection. Fall protection and fall protection components provided by the steel erector shall not remain in the area where steel erection activity has been completed, unless responsibility has been assumed by the controlling contractor or its authorized representative: - (i) Has directed the steel erector to leave the fall protection in place; and - (ii) Has inspected and accepted control and responsibility of the fall protection prior to authorizing persons other than steel erectors to work in the area. - (23) 29 C.F.R. §1926.761 is amended to read as follows: - The following provisions are supplemental to the requirements regarding the hazards addressed in this chapter. - (A) Training personnel. Training required by this section shall be provided by a qualified person(s). - (B) Fall hazard training. The employer shall train each employee exposed to a fall hazard in accordance with the requirements of this section. The employer shall institute a training program and ensure employee participation in the program. - (i) The recognition and identification of fall hazards in the work area; - (ii) The use and operation of the fall protection systems to be used by the employer and in the systems that may be encountered on the jobsite; e.g., guardrail systems

Source excerpt

## 29 CFR 1926 (OSHA) walking/working surface, shall be protected from falling by the use of a guardrail system, a safety net system, or a personal fall arrest system. - (15) Walking/working surfaces not otherwise addressed. Except as provided in §1926.500(a)(2) or in §1926.501 (b)(1) through (b)(14), each employee on a walking/working surface 6 feet (1.8 m) or more above lower levels shall be protected from falling by a guardrail system, safety net system, or personal fall arrest system. - (c) Protection from falling objects. When an employee is exposed to falling objects, the employer shall have each employee wear a hard hat and shall implement one of the following measures: - (1) Erect toeboards, screens, or guardrail systems to prevent objects from falling from higher levels; or, - (2) Erect a canopy structure and keep potential fall objects far enough from the edge of the higher level so that those objects would not go over the edge if they were accidentally displaced; or, - (3) Barricade the area to which objects could fall, prohibit employees from entering the barricaded area, and keep objects that may fall far enough away from the edge of a higher level so that those objects would not go over the edge if they were accidentally displaced.