please give me the glove policy for EAG. Can you frame this in a toolbox talk format on glove and hand safety

Source excerpt

# Workplace specifics Describe any additional company glove policies here, such as glove supply and replacement, cleaning policies or rules about use of gloves around machinery with moving parts. Washington State Department of Labor & Industries 22

Source excerpt

# Glove Use and Care # Use the right glove for the job Don't use fabric or leather gloves to handle liquid chemicals. BIX STRIPPER REMOVES BIX VARNISH PAINT AND STAIN STRIPPER REMOVES PAINT No! Yes! Washington State Department of Labor & Industries 15

Source excerpt

# Chemical-Resistant Gloves # Chemical glove selection - No single glove material will protect against all chemicals. - Gloves are selected according to the type of chemical. - Good chemical gloves are made of Viton®, butyl, nitrile, neoprene, PVC or PVA or combinations of these. Washington State Department of Labor & Industries 19

Source excerpt

# Glove Size & Fit Gloves come in many sizes. ## Use properly fitting gloves that give you the needed dexterity. A better fit Too big Washington State Department of Labor & Industries 12

Source excerpt

# Glove Wear for Wet Cement Work (cont.) If you remove your gloves during work, wash again with clean water and soap, or you may carry contaminants into your gloves. If you have no clean water, try carrying a clean damp wash cloth or disposable towelettes. Before removing your gloves, always clean off the outsides. Follow the manufacturer's instructions. To remove gloves, loosen them on both hands. Hold hands down so contaminated water will not drip onto skin or clothing. Keeping gloves down, remove the first glove only to the fingers. The cuff of the glove will remain over your palm. Now, grabbing the second glove with the first glove, remove the second glove. The first glove should slip off. Try to handle gloves by the insides only. Don't touch the outsides.

Source excerpt

# Chemical Protective Clothing - Glove Selection (cont.) ## What should I know first about chemical protective clothing? (cont.) The SDS should specify the appropriate type of chemical protective material needed(e.g., neoprene, butyl rubber). If this information is missing, contact the supplier or manufacturer of the product. Manufacturers of chemical protective gloves and clothing may also assist customers in making the appropriate choices. ## What is meant by permeation rate, breakthrough time, and degradation? Permeation rate is the rate or speed at which the chemical will move through the material. It is measured in a laboratory and is expressed in units such as milligrams per square meter per second (or some other [weight of chemical] per [unit area of material] per [unit of time]). The higher the permeation rate, the faster the chemical will move through the material. Permeation is different from penetration. Penetration occurs when the chemical leaks through seams, pinholes and other imperfections in the material: permeation occurs when the chemical diffuses or travels through intact material. Breakthrough time is the time it takes a chemical to permeate completely through the material. It is determined by applying the chemical on the glove exterior and measuring the time it takes to detect the chemical on the inside surface. The sensitivity of the analytical instruments used in these measurements influences when a chemical is first detected. The breakthrough time gives some indication of how long a glove can be used before the chemical will permeate through the material. Degradation is a measurement of the physical deterioration of the material due to contact with a chemical. The material may get harder, stiffer, more brittle, softer, weaker, or may swell. The worst example is that the material may actually dissolve in the chemical. ## How do I choose the right material for the job? The appropriate material for each job must be chosen with care. Bef…

Source excerpt

# Chemical-Resistant Gloves Facts - Chemical-resistant gloves are not totally "chemical-proof" - Chemicals will eventually penetrate the gloves over time. - Chemicals will also break down (swell, crack or weaken) the glove material over time. - The thicker the glove, the more resistant it is to chemicals. Thick is better than Thin Washington State Department of Labor & Industries 18

Source excerpt

# Chemical Protective Clothing - Glove Selection (cont.) ## What are some other points to remember about skin and hand protection? (cont.) - Choose hand protection that adequately protects from the hazard(s) of a specific job and adequately meets the specific tasks involved in the job (such as flexibility or dexterity). - Follow the manufacturer's instructions for care, decontamination, and maintenance of gloves. - Be aware that some materials may cause reactions in some workers, such as allergies to latex. Offer alternatives where possible. - Make sure the gloves fit properly. - Make sure gloves cover all of the exposed skin. Gloves should be long enough so that there is no gap between the glove and sleeve. - Do not wear gloves with metal parts near electrical equipment. - Do not use worn or torn gloves. - Clean gloves as instructed by the supplier. - Inspect and test gloves for defects before using. - Test all rubber or synthetic gloves for pin holes or leaks by inflating them (see figures below). Know how to remove and either clean or dispose of used gloves, as appropriate. How can gloves be tested for holes or leaks? Figure 1 Hold the cuff as illustrated, with thumbs inside, and stretch the cuff slightly. Chemical Protective Clothing - Glove Selection CCOHS

Source excerpt

# Glove Use & Care Some common-sense rules about gloves Replace gloves if they have cuts, tears, holes or defects. - Make sure gloves are the right length for the job. Washington State Department of Labor & Industries 14

Source excerpt

# Glove Limitations ✔ Gloves can get caught in rotating machinery. ✔ Some people are allergic to latex gloves. ✔ Gloves can actually cause more problems if chemicals get inside glove. ✓ Gloves can fail in conditions of extreme temperatures, high mechanical force, high vibration or handling extremely harsh chemicals. Washington State Department of Labor & Industries 11

Source excerpt

# HAND PROTECTION (cont.) ## CONTACT HAZARDS Contact hazards include anything that causes cuts to the hand or fingers. These risks include sharp edges on tools, protruding nails, sharp edges, packaging, containers, and other materials. While most contact hazards focus on cutting or puncturing the hand or fingers, items that can cause burns, such as chemicals, electrical currents, or extreme temperatures, also fall into the category. ## PREVENTING HAND INJURIES According to the Bureau of Labor Statistics (BLS), 70% of workers who experienced hand injuries were not wearing gloves. Therefore, the first and most essential step in preventing hand injuries on construction sites is to use the right pair of gloves for your task. According to research by Industrial Safety & Hygiene News (ISHN), "using the right pair of gloves for the task will reduce hand injuries by more than 60%". Gloves should fit properly and be worn by the worker when required or necessary to see decreases in hand injuries. Gloves must also fit the task being performed (e.g., thermal-rated gloves for hot and cold, cut-rated gloves for handling sharp objects, chemical (e.g., Nitrile, Butyl, etc.} rated gloves for handling hazardous chemicals, etc.). ## SELECTING THE RIGHT GLOVES FOR THE TASK There are many factors to consider when choosing the right glove for a given task. For example, the amount of dexterity needed to perform a particular job must be weighed against the glove material recommended for the hazard(s) (e.g., cut, electrical, thermal, or chemical resistance} to protect your hands from an injury effectively. In some cases, mainly when working with delicate objects where fine dexterity is crucial, a bulky glove may become more hazardous in specific scenarios. Use the OSHA PPE Guide to select the appropriate glove for the task/hazards you will be exposed to. ## REFERENCES WAC [redacted identifier] WAC [redacted identifier] WAC 296-800-[redacted postal code] Centers for Disease Contro…

Source excerpt

# Glove Use & Care - Your hands should be clean before using gloves. - Fabric and leather gloves should be cleaned regularly or discarded. - Latex gloves should not be used by latex-sensitive people Washington State Department of Labor & Industries 13

Source excerpt

# Chemical Protective Clothing - Glove Selection (cont.) ## What are some other points to remember about skin and hand protection? (cont.) If large numbers need testing use a compressed air jig. Figure 5 Double-roll the cuff over and grip with your hand. ## What is meant by a workplace evaluation? The selected glove should be carefully tested in the actual job conditions. In some situations, it may be desirable to do laboratory tests on the gloves using the American Society for Testing and Materials (ASTM) methods. This testing is especially important if you do not have information about the permeation time of a particular chemical you are using or if you are using mixtures of solvents or chemicals. Some glove manufacturers may undertake these tests for their customers. ## Does the use of chemical protective clothing require a PPE program? The employer must have a process in place to ensure a competent person reviews the selection and use of chemical protective clothing. If chemical protective gloves and clothing are required, there should be a complete PPE program in place that includes - the training of workers in the appropriate use and care of protective gear and - the selection, fitting, maintenance and inspection of the protective clothing and gloves. A successful program will ensure that any changes in chemicals used are accounted for, will regularly check for any issues, and will result in necessary changes or improvements. Chemical Protective Clothing - Glove Selection CCOHS