Distance securitaire dun levage avec une charge

Safe Clearance Distance for Lifting Operations with Suspended Loads ===================================================================

Maintaining a safe clearance distance during lifting operations with suspended loads is crucial for preventing accidents and ensuring the safety of personnel. This document outlines the necessary clearance distances and safety measures to be observed during such operations, particularly in relation to power lines and fall zones.

Power Line Safety

---

Minimum Clearance Distances

When operating equipment near power lines, it is essential to maintain the minimum clearance distances to prevent electrical contact. These distances vary depending on the voltage of the power line:

• For lines rated 50 kV or below, the minimum clearance between the lines and any part of the crane or load must be 10 feet.
• For lines rated over 50 kV, the minimum clearance must be 10 feet plus 0\.4 inch for each 1 kV over 50 kV, or twice the length of the line insulator, but never less than 10 feet.
• In transit with no load and boom lowered, the equipment clearance must be a minimum of 4 feet for voltages less than 50 kV, and 10 feet for voltages over 50 kV, up to and including 345 kV, and 16 feet for voltages up to and including 750 kV.

Qualified Person and Planning

A qualified person, such as a registered professional engineer or the utility owner/operator, must determine the minimum clearance distance to prevent electrical contact, considering on-site conditions such as atmospheric conductivity, wind conditions, and the degree of sway in the power line. A planning meeting involving the equipment user, utility owner/operator (or registered professional engineer), equipment operator, and other workers in the area is crucial to review procedures for preventing breaches of the minimum approach distance and electrocution.

Preventive Measures

• Use a dedicated spotter who is in continuous contact with the operator to provide timely information and maintain the required clearance distance.
• Erect and maintain an elevated warning line or barricade, equipped with flags or similar high-visibility markings, in view of the operator to prevent electrical contact.
• Consider using an insulating link/device installed between the end of the load line and the load.

Power lines are presumed to be energized unless the utility owner/operator confirms that the power line has been de-energized and visibly grounded at the worksite.

Fall Zone Safety

---

Keeping Clear of the Load

While the operator is not moving a suspended load, no employee should be within the fall zone, except for those engaged in specific tasks:

• Hooking, unhooking, or guiding a load.
• The initial attachment of the load to a component or structure.
• Operating a concrete hopper or concrete bucket.

When employees are within the fall zone for these tasks, ensure that:

• The materials being hoisted are rigged to prevent unintentional displacement.
• Hooks with self-closing latches or their equivalent are used.
• The materials are rigged by a qualified rigger.

During tilt-up or tilt-down operations, no employee must be directly under the load, and only essential employees are permitted in the fall zone.

Work Area Control

Where the equipment's rotating superstructure poses a risk of striking or crushing employees, implement the following measures:

• Train employees to recognize struck-by and pinch/crush hazard areas.
• Erect and maintain control lines, warning lines, railings, or similar barriers to mark the boundaries of the hazard areas. If barriers are not feasible, use warning signs and high-visibility markings on the equipment.

Before an employee goes to a location in the hazard area that is out of view of the operator, ensure the operator is informed. The operator must not rotate the superstructure until receiving confirmation that the employee is in a safe position.

General Safety Practices

---

Pre-Lift Planning and Meetings

Conduct a pre-lift meeting to review applicable safety requirements and procedures.

Personnel Platform Safety

When using personnel platforms, ensure that:

• The platform is not loaded in excess of its rated capacity.
• The number of employees occupying the platform does not exceed the number required for the work.
• Materials and tools are secured to prevent displacement and evenly distributed within the platform.
• Employees keep all parts of the body inside the platform during raising, lowering, and positioning.
• Employees use a body belt/harness system with a lanyard attached to a structural member within the platform.

Trial Lifts and Inspections

Perform a trial lift with the unoccupied personnel platform loaded to at least the anticipated lift-weight before each shift.

• Inspect the equipment, base support, and personnel platform after the trial lift to identify any defects or problems.
• Immediately prior to each lift, hoist the platform a few inches and inspect it to ensure it is secure and properly balanced.
• Conduct a proof test of the platform and rigging to 125% of the platform's rated capacity before hoisting employees.

Authority to Stop Operation

Any person must have the authority to stop the operation at any time to ensure safety.

By adhering to these clearance distances and safety measures, employers can significantly reduce the risk of accidents and ensure the safety of personnel during lifting operations with suspended loads.

References

---

OSHA Construction Industry Standards Requiring Programs, Inspections, Procedures Records and/or Training (NCDOL)

Occupational Safety and Health Standards (OSHA 29 CFR 1910\)

Safety Standards for General Safety and Health Standards (Chapter 296-24 WAC)

Construction Safety and Health Standards (MIOSHA)

Safety and Health Regulations for Construction (OSHA 29 CFR 1926\)

Occupational Health and Safety Regulations, 2012 (N.L. Reg. 5/12\)

Safety powered by SALUS