Skip to content
All safety questions
Asked by a personUnited Statesen-US

Safe work procedure for pouring concrete

A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.

Rosie's answer

Published by SALUS

Safe Work Procedure for Pouring Concrete ========================================

Document Number: \[SWP-NUMBER]

Revision Date: \[DATE]

Next Review Date: \[NEXT REVIEW DATE]

Department: \[DEPARTMENT NAME]

1\. Scope

This safe work procedure outlines the steps to be followed when pouring concrete to ensure the safety of all personnel involved. It includes information on hazard identification, risk assessment, control measures, required personal protective equipment (PPE), and emergency procedures. This procedure applies to all workers involved in concrete pouring activities.

2\. Definitions

Portland Cement A hydraulic cement consisting of finely ground clinker, comprising hydraulic calcium silicates, usually containing one or more of the forms of calcium sulfate as an interground addition. Dermatitis Inflammation of the skin. Skin contact with Portland cement can cause inflammation of the skin, referred to as dermatitis. Signs and symptoms of dermatitis can include itching, redness, swelling, blisters, scaling, and other changes in the normal condition of the skin. [4]

NIOSH National Institute for Occupational Safety and Health

3\. Responsibilities

3\.1 Supervisors

  • Ensure all workers are properly trained and competent to perform the task.
  • Provide all necessary equipment and PPE in good working condition.
  • Conduct regular site inspections to ensure compliance with this procedure.
  • Enforce all safety rules and regulations.

3\.2 Workers

  • Follow all instructions and procedures outlined in this document.
  • Use all required PPE as specified.
  • Report any hazards or unsafe conditions to the supervisor immediately.
  • Participate in pre-job briefings and safety meetings.

3\.3 Health and Safety Representative

  • Monitor workplace safety and health conditions.
  • Participate in incident investigations.
  • Provide recommendations for improving safety procedures.

4\. Potential Hazards and Risks

HazardRiskControl Measures
Dust inhalation [3]Respiratory irritation, silicosisUse a NIOSH-approved dust mask or filtering face piece in poorly ventilated areas or when permissible exposure limits may be exceeded. Ensure adequate ventilation.
Skin contact with wet concrete [1] [1]Dermatitis, chemical burnsWear gloves of adequate length to offer appropriate skin protection from splashes. Wear rubber boots when stepping in concrete. Immediately remove all soiled and contaminated clothing. Wash hands before breaks and at the end of work. Avoid contact with the eyes and skin.
Eye contact with concrete dust or splashes [2]Serious eye damageWear approved eye protection (properly fitted dust- or splash-proof chemical safety glasses).
Lifting heavy bags of concrete mixBack strain, muscle injuryUse proper lifting techniques. Get assistance when lifting heavy bags. Use mechanical aids where possible.
Slips, trips, and fallsInjuries from fallsMaintain good housekeeping. Clean up spills immediately. Wear slip-resistant footwear.
Mixing concrete [1]Exposure to dust and potential splashesEnsure good ventilation/exhaustion at the workplace. DO NOT BREATHE DUST. In dusty environments, the use of an OSHA, MSHA or NIOSH approved respirator and tight fitting goggles is recommended. Wear appropriate PPE.
Manual handling of concreteMusculoskeletal disordersUse mechanical aids wherever possible (e.g., wheelbarrows, concrete pumps). Rotate tasks to reduce repetitive motions.

5\. Personal Protective Equipment (PPE)

Wear appropriate PPE.

  • Gloves: Wear gloves of adequate length to offer appropriate skin protection from splashes. Nitrile, Butyl and PVC gloves have been found to offer adequate protection for incidental contact. [1]
  • Eye Protection: Wear approved eye protection (properly fitted dust- or splash-proof chemical safety glasses). [2]
  • Rubber Boots: Wear rubber boots when stepping in concrete. You cannot rely on pain to alert you to cement burns. Portland cement can cause dermatitis or sensitization. [1]
  • Respiratory Protection: A NIOSH-approved dust mask or filtering face piece is recommended in poorly ventilated areas or when permissible exposure limits may be exceeded. [3]
  • Protective Clothing: Wear appropriate protective clothing to minimize skin exposure.

6\. Equipment and Tools

Inspect all equipment and tools before use.

  • Concrete Mixer: Used for mixing concrete. Inspect for any damage before use. Ensure all safety guards are in place and functioning properly.
  • Wheelbarrow: Used for transporting concrete. Check tire pressure and ensure handles are secure.
  • Shovels and Rakes: Used for moving and spreading concrete. Inspect for damage or wear before use.
  • Vibrator: Used to consolidate concrete. Ensure the power cord is in good condition and the unit is properly grounded.

7\. Pre-Job Requirements

7\.1 Training and Competency

Training and Competency: All workers must be trained and competent in the safe pouring of concrete, including hazard awareness, PPE requirements, and emergency procedures.

7\.2 Pre-Job Briefing

Pre-Job Briefing: A pre-job briefing must be conducted before starting any concrete pouring activity to discuss the scope of work, potential hazards, and control measures.

7\.3 Work Area Preparation

Work Area Preparation: The work area must be properly prepared before starting any concrete pouring activity. This includes ensuring adequate lighting, ventilation, and access.

8\. Safe Work Procedure Steps

  1. Pre-Job Inspection: Inspect all equipment and tools before use to ensure they are in good working condition. Check the work area for any hazards and correct them before starting work.
  2. Set Up Mixing Area: Set up the concrete mixer on a stable, level surface. Ensure there is adequate ventilation in the mixing area.
  3. Mix Concrete: Follow the manufacturer's instructions for mixing the concrete. Add water gradually until the desired consistency is achieved. Do not mix with other chemical products, except as indicated by the manufacturer. [1]
  4. Transport Concrete: Use a wheelbarrow or other suitable equipment to transport the concrete to the pouring location. Avoid overfilling the wheelbarrow.
  5. Pour Concrete: Pour the concrete into the designated area. Use shovels and rakes to spread the concrete evenly.
  6. Consolidate Concrete: Use a vibrator to consolidate the concrete and remove any air pockets.
  7. Clean Up: Clean all equipment and tools after use. Dispose of any waste concrete properly. Do not allow to enter sewers/ surface or ground water. Good housekeeping is important to prevent accumulation of dust. [1]

[1]

  1. Curing: Follow proper curing procedures to ensure the concrete sets correctly.

9\. Precautions and Safety Measures

  • Ensure good ventilation/exhaustion at the workplace. [1]
  • DO NOT BREATHE DUST. In dusty environments, the use of an OSHA, MSHA or NIOSH approved respirator and tight fitting goggles is recommended. [1]
  • Keep away from foodstuffs, beverages and feed. Immediately remove all soiled and contaminated clothing. Wash hands before breaks and at the end of work. Avoid contact with the eyes and skin. [1]
  • Do not allow water to contact the product until time of use to preserve product utility. [1]
  • You cannot rely on pain to alert you to cement burns. Therefore precautions must be taken to prevent all contact with Portland cement.

10\. Emergency Procedures

10\.1 General Emergency Response

In any emergency situation, the primary concern is the safety of all personnel. Assess the situation, provide first aid, and contact emergency services as needed.

10\.2 Specific Emergency Scenarios

  • Skin contact with wet concrete: Immediately remove contaminated clothing and rinse the affected area with plenty of water. If irritation or burns develop, seek medical attention.
  • Eye contact with concrete dust or splashes: Rinse eyes cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately seek medical advice.
  • Inhalation of concrete dust: Remove person to fresh air and keep comfortable for breathing. If respiratory irritation or difficulty breathing occurs, seek medical attention.

10\.3 Emergency Contact Information

In case of emergency, contact emergency services immediately.

11\. Incident Reporting and Investigation

All incidents, including near misses, must be reported to the supervisor immediately. A written report must be submitted within 24 hours of the incident.

All reported incidents will be investigated to determine the root cause and to implement corrective actions to prevent recurrence.

Approved by: \[NAME AND POSITION]

Date: \[APPROVAL DATE]

Safety powered by SALUS

4 source record(s)

Sources used for this answer

[1] QUIKRETE - C4: Portland Cement Based Concrete Products

Page 6

Open source document

Source excerpt

# CEMENT & CONCRETE PRODUCTS™ (cont.) ## SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND STORAGE (cont.) QUIKRETE GHS SAFETY DATA SHEET # CEMENT & CONCRETE PRODUCTS™ ## 7.1 Handling Precautions for safe handling: Ensure good ventilation/exhaustion at the workplace. DO NOT BREATHE DUST. In dusty environments, the use of an OSHA, MSHA or NIOSH approved respirator and tight fitting goggles is recommended. Wear appropriate PPE (See section 8). Do not mix with other chemical products, except as indicated by the manufacturer. Do not get in eyes, on skin or clothing. Good housekeeping is important to prevent accumulation of dust. ## 7.2 Storage Requirements to be met by storerooms and receptacles: No special requirements. Information about storage in one common storage facility: Not required. Further information about storage conditions: Keep out of the reach of children. Keep container tightly closed and prevent exposure to humidity. Do not allow water to contact the product until time of use to preserve product utility. SECTION VIII - EXPOSURE CONTROL MEASURES I PERSONAL PROTECTION 8.1 Components with limit values that require monitoring at the workplace: Hazardous Components CAS No. PEL (OSHA) TLV (ACGIH) <table><tr><th>Hazardous Components</th><th>CAS No.</th><th>require monitoring PEL (OSHA) mg/M³</th><th>workplace: TLV (ACGIH) mg/M³</th></tr><tr><td>Silica Sand, crystalline</td><td>[redacted postal code]-60-7</td><td>0.05</td><td>0.025 (resp)</td></tr><tr><td>Portland Cement</td><td>[redacted postal code]-15-1</td><td>5 (resp) 15 (total)</td><td>10 (resp)</td></tr><tr><td>Lime</td><td>[redacted postal code]-62-0</td><td>5</td><td>5</td></tr><tr><td>Pulverized Limestone</td><td>[redacted postal code]-65-3</td><td>5 (resp) 15 (total)</td><td>10 (resp)</td></tr></table> ## 8.2 Exposure Controls Use ventilation adequate to keep exposures below recommended exposure limits. ## 8.3 General protective and hygienic measures Keep away from foodstuffs, beverages a…

[2] QUIKRETE - C11: Portland Cement Based Concrete Products

Page 6

Open source document

Source excerpt

# CEMENT & CONCRETE PRODUCTS™ (cont.) ## SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND STORAGE (cont.) QUIKRETE GHS SAFETY DATA SHEET # CEMENT & CONCRETE PRODUCTS™ mix with other chemical products, except as indicated by the manufacturer. Do not get in eyes, on skin or clothing. Good housekeeping is important to prevent accumulation of dust. ## 7.2 Storage Requirements to be met by storerooms and receptacles: No special requirements. Information about storage in one common storage facility: Not required. Further information about storage conditions: Keep out of the reach of children. Keep container tightly closed and prevent exposure to humidity. Do not allow water to contact the product until time of use to preserve product utility. ## SECTION VIII - EXPOSURE CONTROL MEASURES / PERSONAL PROTECTION 8.1 Components with limit values that require monitoring at the workplace: <table><tr><th>Hazardous Components</th><th>CAS No.</th><th>PEL (OSHA) mg/M³</th><th>TLV (ACGIH) mg/M³</th></tr><tr><td>Silica Sand, crystalline</td><td>[redacted postal code]-60-7</td><td>0.05</td><td>0.025 (resp)</td></tr><tr><td>Portland Cement</td><td>[redacted postal code]-15-1</td><td>5 (resp) 15 (total)</td><td>10 (resp)</td></tr><tr><td>Hydrated Lime</td><td>7719-01-9</td><td>5</td><td>5</td></tr></table> 8.2 Exposure Controls Use ventilation adequate to keep exposures below recommended exposure limits. ## 8.3 General protective and hygienic measures Keep away from foodstuffs, beverages and feed. Immediately remove all soiled and contaminated clothing. Wash hands before breaks and at the end of work. Avoid contact with the eyes and skin. - 8.3a Personal protective equipment - Protection of hands and feet: - Wear gloves of adequate length to offer appropriate skin protection from splashes. Nitrile, Butyl and PVC gloves have been found to offer adequate protection for incidental contact. Wear rubber boots when stepping in concrete. You cannot rely on pain to alert you to ce…

[3] QUIKRETE - C5: Portland Cement Based Concrete Products

Page 6

Open source document

Source excerpt

# CEMENT & CONCRETE PRODUCTS™ (cont.) ## SECTION VI - ACCIDENTAL RELEASE MEASURES (cont.) QUIKRETE GHS SAFETY DATA SHEET # CEMENT & CONCRETE PRODUCTS™ ## 6.2 Methods and material for containment and cleaning up: Do not allow to enter sewers/ surface or ground water. Dispose of unwanted materials and containers properly in accordance with all regulations. ## SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND STORAGE ## 7.1 Handling Precautions for safe handling: Ensure good ventilation/exhaustion at the workplace. DO NOT BREATHE DUST. In dusty environments, the use of an OSHA, MSHA or NIOSH approved respirator and tight fitting goggles is recommended. Wear appropriate PPE (See section 8).Do not mix with other chemical products, except as indicated by the manufacturer. Do not get in eyes, on skin or clothing. Good housekeeping is important to prevent accumulation of dust. ## 7.2 Storage Requirements to be met by storerooms and receptacles: No special requirements. Information about storage in one common storage facility: Not required. Further information about storage conditions: Keep out of the reach of children. Keep container tightly closed and prevent exposure to humidity. Do not allow water to contact the product until time of use to preserve product utility. ## SECTION VIII - EXPOSURE CONTROL MEASURES I PERSONAL PROTECTION 8.1 Components with limit values that require monitoring at the workplace: Hazardous Components CAS No. <table><tr><th>Hazardous Components</th><th>CAS No.</th><th>PEL (OSHA) mg/M³</th><th>TLV (ACGIH) mg/M³</th></tr><tr><td>Silica Sand, crystalline</td><td>[redacted postal code]-60-7</td><td>0.05</td><td>0.025 (resp)</td></tr><tr><td>Portland Cement</td><td>[redacted postal code]-15-1</td><td>5 (resp) 15 (total)</td><td>10 (resp)</td></tr><tr><td>Lime</td><td>[redacted postal code]-62-0</td><td>5</td><td>5</td></tr></table> ## 8.2 Exposure Controls Use ventilation adequate to keep exposures below recommended exposure limits. ## 8…

[4] QUIKRETE - C4: Portland Cement Based Concrete Products

Page 5

Open source document

Source excerpt

# CEMENT & CONCRETE PRODUCTS™ (cont.) ## SECTION IV - FIRST AID MEASURES (cont.) QUIKRETE GHS SAFETY DATA SHEET # CEMENT & CONCRETE PRODUCTS™ Skin contact with Portland cement can also cause inflammation of the skin, referred to as dermatitis. Signs and symptoms of dermatitis can include itching, redness, swelling, blisters, scaling, and other changes in the normal condition of the skin. Signs and symptoms of burns include the above and whitening, yellowing, blackening, peeling or cracking of skin. The Portland cement in this product may cause allergic contact dermatitis in sensitized individuals. This overreaction of the immune system can lead to severe inflammation. Sensitization may result from a single exposure to the low levels of Cr (VI) in Portland cement or repeated exposures over months or years. Sensitization is long lasting and, after sensitization, even very small quantities can trigger the dermatitis. Sensitization is uncommon. Individuals who experience skin problems, including seemingly minor ones, are advised to seek medical attention. Eye Contact: Causes serious eye damage. Symptoms may include discomfort or pain, excess blinking and tear production, with marked redness and swelling of the conjunctiva. Ingestion: May be harmful if swallowed. Ingestion may cause discomfort and/or distress, nausea or vomiting. 4.3 Indication of immediate medical attention and special treatment needed: Immediately seek medical advice if symptoms are significant or persist. ## SECTION V - FIRE FIGHTING MEASURES - 5.1 Flammability of the Product: Non-flammable and non-combustible - 5.2 Suitable extinguishing agents: Treat for surrounding material - 5.3 Special hazards arising from the substance or mixture: None - 5.3a Products of Combustion: None - 5.3b Explosion Hazards in Presence of Various Substances: Non-explosive in presence of shocks ## SECTION VI - ACCIDENTAL RELEASE MEASURES - 6.1 Personal precautions, protective equipment and emergency procedur…

Related Q&A

Keep exploring.

Human questionGeneral

i want to make a JSA for replacement of busted hyd hose of a drill machine smartrock T45

Hydraulic Hose Replacement on Smartrock T45 Drill Machine ========================================================= *Assessment Date:** \[DATE] *Assessor:** \[ASSESSOR NAME] *Department/Area:** \[DEPARTMENT/AREA] *Review Date:** \[REVIEW DATE] 1\. Assessment Scope This Job Safety Analysis (JSA) covers the hydraulic

Read the thread
Human questionGeneral

rail construction

Rail Construction and Maintenance Safety ======================================== Document Number: \[SWP-NUMBER] Revision Date: \[DATE] Next Review Date: \[NEXT REVIEW DATE] Department: \[DEPARTMENT NAME] 1\. Scope This safe work procedure (SWP) outlines the safety requirements for all rail construction and maintenance

Read the thread
Human questionGeneral

NORMS COP

Safety Procedures and Risk Assessments in NORMS COP Documentation ================================================================= This document outlines the safety procedures and risk assessments that should be included in a company's NORMS Code of Practice (COP) documentation. It is based on industry best practices

Read the thread
Human questionGeneral

Write a toolbox talk on Hand and Finger injuries

Hand and Finger Injury Prevention ================================= *Date:** 2026-02-18 *Duration:** \[DURATION] minutes *Presenter:** \[PRESENTER NAME] *Location:** \[LOCATION] Objective To increase awareness of hand and finger injury hazards and promote preventative measures in the workplace. Introduction Our hands

Read the thread
Human questionUS

Write a pre-task plan for Daily safety briefing

A compliant pre-task plan and daily safety briefing should be completed before work starts and updated whenever conditions, scope, personnel, or controls change. The process should be site-specific and should use a documented job hazard analysis (JHA/JSA) to break the work into steps, identify hazards for each step

Read the thread
Discussion thread

Add your experience.

Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.

New contributions are temporarily closed while the moderation queue is configured.

Community answers(0)

No community answers have been approved yet.

Comments on Rosie's answer(0)

No comments have been approved yet.

Ready to put operational safety to work?

Join 400K users across 150K sites already on SALUS.

Request a demo

No commitment · 30-minute personalized walkthrough