Skip to content
All safety questions
Asked by a personGeneral — US and Canadaen-US

Write a risk assessment for enoc fuel station c store front side led screen installation, remove of existing billboard , structure installation , screen , acp cladding

A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.

Rosie's answer

Published by SALUS

A suitable RAMS for installing a front-side LED screen at an operating ENOC fuel station C-store should classify the work as high-risk construction in a live fuel-retail environment and require a task-by-task hazard assessment before work starts. The assessment should apply the hierarchy of controls, prioritizing elimination, engineering controls, and administrative controls before PPE. Particular attention is required for work at height, lifting, electrical isolation, hot-work potential, vehicle/public interface, and ignition control near fuel operations. [3] [6]

Recommended method statement controls:

  1. Pre-job planning: obtain ENOC/site approval, verify structural design and fixing details for the steel support and LED screen, review underground/overhead services, define hazardous zones around dispensers/vents/tanker routes, and schedule work during low-traffic or temporary shutdown periods where needed.
  2. Permit to work: issue a site-specific permit package covering general work permit, work-at-height permit, lifting permit, electrical isolation/lockout permit, and hot-work permit if any cutting, grinding, welding, or spark-producing activity is unavoidable. No work should begin until permits are authorized and displayed at site.
  3. Isolation and fuel-station controls: isolate and lock out electrical supplies feeding the existing billboard/signage and any affected circuits; where work could create ignition sources, suspend nearby fuel dispensing, prohibit tanker unloading, control vehicle movements, and maintain exclusion distances from dispensers, fill points, vents, and hazardous locations.
  4. Removal of existing billboard: inspect stability before dismantling, disconnect and prove dead all electrical feeds, remove panels in a controlled sequence, prevent dropped objects, and lower components by mechanical means rather than free-hand throwing or uncontrolled cutting.
  5. Steel support installation: use engineered lifting plans and certified lifting gear; verify load weights, crane/MEWP capacities, ground bearing, and exclusion zones; never allow suspended loads over workers, customers, or occupied public areas.
  6. LED screen mounting: install from MEWP/scaffold where practicable, use tag lines to control swing, secure tools/materials against falling, and connect modules only after structural supports are fully fixed and inspected.
  7. ACP cladding works: control sharp-edge and manual-handling hazards, manage dust/flying particles from cutting/drilling, and prohibit hot work in hazardous areas unless the area is gas-tested, made safe, and specifically authorized.
  8. Electrical works: all temporary and permanent wiring should be by competent electricians; isolate, lock out, test for dead, protect cables from damage, use suitable IP-rated equipment, provide earthing/bonding as required, and verify no energized exposed parts remain accessible.
  9. Work at height: avoid ladder-only methods except for short-duration light tasks; prefer MEWP or properly designed platform/scaffold; use a fall protection plan, inspected anchors, full body harness/lanyard where required, and a rescue plan before starting.
  10. Public and traffic safety: barricade the work zone, segregate pedestrians and vehicles, assign trained banksmen/signallers, maintain emergency access and customer egress, and use warning signs, cones, flashing beacons, and high-visibility controls around delivery and parking routes.
  11. Fire and explosion prevention: prohibit smoking/open flames, use only intrinsically safe or suitably rated equipment within hazardous areas, control static and ignition sources, keep extinguishers immediately available, assign a fire watch for any permitted hot work, and stop work immediately if fuel odor, leak, or gas alarm occurs.
  12. Emergency preparedness: brief all workers on alarm raising, emergency shutdown arrangements, spill/fire response, rescue from height, first aid, ambulance access, and muster points; maintain continuous communication and site supervision throughout the job.

[7] [9] [4] For an operating fuel station, the key intolerable hazards are ignition of flammable vapors, falls from height, collapse or dropped loads during billboard removal and steel erection, electric shock/arc, and struck-by incidents involving customers, vehicles, cranes, or MEWPs. The safest approach is to eliminate ignition sources and minimize simultaneous operations with fuel dispensing. If hot work cannot be eliminated, it should only proceed under a dedicated hot-work permit, after area gas testing, isolation of affected fuel operations, removal/control of combustibles, provision of extinguishers, and continuous fire watch. [4] [5] [7]

Minimum contractor HSE controls:

  • Approved RAMS, task risk assessment, lifting plan, rescue plan, and permit-to-work system in place before mobilization.
  • Competent supervisor present at all times; only trained and authorized riggers, electricians, MEWP operators, scaffolders, and installers to perform the work.
  • Daily toolbox talk covering hazardous area restrictions, emergency shutdown, exclusion zones, dropped-object prevention, and stop-work authority.
  • Inspection records for cranes/MEWPs/lifting gear/fall-arrest equipment; defective equipment removed from service.
  • Barricades, signage, and access control to prevent unauthorized entry by customers and third parties.
  • Good housekeeping, controlled material storage, secured tools, and waste removal to avoid trip, fire, and falling-object hazards.
  • Weather monitoring; stop lifting and work-at-height activities during high winds, lightning, poor visibility, or unsafe conditions.
  • Documented PPE training, inspection, maintenance, and enforcement.

[6] [4] [9] Typical PPE for this job:

  • Safety helmet suitable for impact; electrical class helmet where electrical exposure exists.
  • Safety glasses with side shields; goggles/face shield for cutting, drilling, grinding, or chemical splash risk.
  • Cut-resistant/general work gloves; chemical-resistant gloves where sealants/solvents/cleaners are used; insulated gloves for electrical tasks as applicable.
  • Steel-toe, slip-resistant, puncture-resistant safety footwear; electrical hazard footwear where required.
  • High-visibility vest/clothing for traffic interface and lifting operations.
  • Full body harness with suitable lanyard/fall-arrest system for work at height where collective protection is not sufficient.
  • Hearing protection when using noisy power tools.
  • Respiratory protection selected to the hazard, such as dust masks for nuisance dust or suitable respirators for welding fumes/organic vapors where exposure assessment requires it.
  • Flame-resistant or static-control clothing where dictated by fuel-station hazardous area assessment and hot-work controls.

[1] [2] [8] [10] For compliance in the UAE, the RAMS should be aligned with applicable UAE federal and emirate-level OSH requirements, civil defense/fire code expectations, DEWA/municipality/electrical rules as applicable, and the fuel-station operator's engineering and HSE standards for hazardous areas, permits, shutdowns, and contractor control. In practice, this means the contractor should ensure: hazardous area classification is reviewed before selecting tools/equipment; electrical and hot-work activities are authorized by permit; lifting equipment and operators are certified; work-at-height systems include rescue arrangements; traffic/public segregation is maintained; first aid and emergency response are coordinated with station management; and all records, inspections, and training are available on site. Because this is a live petroleum retail environment, the station operator's permit, isolation, and hazardous-area rules should be treated as mandatory site controls in addition to general construction HSE law. [4] [11] [9]

A practical residual-risk summary is: very high risk unless the station environment is tightly controlled. The job should not proceed if fuel leaks are present, hazardous area restrictions are unclear, permits are not approved, lifting plans are incomplete, weather is unsafe, rescue arrangements are absent, or public exclusion cannot be maintained. The preferred execution sequence is: site survey and approvals; permit issue and isolations; barricading and traffic control; electrical disconnection and proof of dead; controlled removal of existing billboard; installation of steel supports; LED screen mounting; ACP cladding; testing/commissioning; final inspection; permit close-out and handover. [3] [7]

11 source record(s)

Sources used for this answer

[1] Personal Protective Equipment (PPE) Guide

Page 18

Open source document

Source excerpt

# Hazard Assessment For PPE (cont.) ## Instructions: (cont.) Option 1 # PPE Hazard Assessment Certification Form *Name of work place: <empty> *Work place address: <empty> *Required for certifying the hazard assessment. Work area(s): <empty> *Assessment conducted by: <empty> *Date of assessment: <empty> Job/Task(s): <empty> Use a separate sheet for each job/task or work area *Required for certifying the hazard assessment. Use a separate sheet for each job/task or work area EYES: Work activities, such as: [ ] abrasive blasting [ ] sanding [ ] chopping [ ] sawing [ ] cutting [ ] grinding [ ] drilling [ ] hammering [ ] welding [ ] punch press operations [ ] other: <empty> Work-related exposure to: [ ] airborne dust [ ] flying particles [ ] blood splashes [ ] hazardous liquid chemicals [ ] intense light [ ] other: <empty> Can hazard be eliminated without the use of PPE? Yes [ ] No [ ] If no, use: [ ] Safety glasses [ ] Side shields [ ] Safety goggles [ ] Dust-tight goggles [ ] Shading/Filter (#<empty>) [ ] Welding shield [ ] Other: <empty> FACE: Work activities, such as: [ ] cleaning [ ] foundry work [ ] welding [ ] siphoning [ ] mixing [ ] painting [ ] pouring molten metal [ ] dip tank operations [ ] other: <empty> Work-related exposure to: [ ] hazardous liquid chemicals [ ] extreme heat/cold [ ] potential irritants: <empty> [ ] other: <empty> Can hazard be eliminated without the use of PPE? Yes [ ] No [ ] If no, use: [ ] Face shield [ ] Shading/Filter (#<empty>) [ ] Welding shield [ ] Other: <empty> HEAD: Work activities, such as: [ ] building maintenance [ ] confined space operations [ ] construction [ ] electrical wiring [ ] walking/walking under catwalks [ ] walking/workng under conveyor belts [ ] walking/workng under crane loads [ ] utility work [ ] other: <empty> Work-related exposure to: [ ] beams [ ] pipes [ ] exposed electrical wiring or components [ ] falling objects [ ] machine parts [ ] other: <empty> Can hazard be eliminated without the us…

[2] Hazard and Risk - Sample Risk Assessment Form

Page 3

Open source document

Source excerpt

# What is a sample risk assessment form? (cont.) ## Sample Risk Assessment Form (cont.) <table><tr><th>Step or task</th><th>Hazard</th><th>Consequences or harm</th><th>Risk</th><th>Priority</th><th>Hazard Controls</th></tr><tr><td>EXAMPLE: Working at heights while on a ladder</td><td>Safety hazard: falling from heights</td><td>Serious injury due to a fall</td><td>High risk</td><td>1</td><td>Follow the hierarchy of controls for working at heights Elimination: when possible, perform work from the ground. Engineering controls: use an elevating work platform when appropriate. Administrative controls:</td></tr><tr><td></td><td></td><td></td><td></td><td></td><td>development of fall protection plans, safe work procedures, emergency response plans for working at heights, and adequate training (including working heights and fall protection training, elevating work platform training, ladder safety, training on safe work procedures and emergency response, etc.). Personal protective equipment: fall arrest system and equipment, head protection, high-visibility. clothing, protective footwear, face and eye protection, emergency response equipment, and other appropriate equipment for the job.</td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td></tr><tr><td></td><td></td><td></td><td></td><td></td><td></td></tr></table> Hazard and Risk - Sample Risk Assessment Form CCOHS

[3] Personal Protective Equipment (PPE) Hazard Assessment Tool

Page 2

Open source document

Source excerpt

## PPE required at this workplace includes (check all that apply): (cont.) OSHA Oregon OSHA Department of Consumer and Business Services Hazard assessment worksheet: Fall protection Salem Central Office [redacted street address]. NE Salem, OR [redacted postal code] Phone: [redacted phone] Toll-free: [redacted phone] osha.oregon.gov Work task: Date ## Potential hazards No hazards requiring fall protection Unguarded surfaces more than 6 or 4 feet above a lower level or any height above dangerous equipment Other hazard: ## PPE required None required Personal fall arrest system Personal fall restraint system Other PPE: 440-5871 (07/23/COM)

[4] Occupational Health and Safety Code (Alberta Regulation 191/2021)

Page 428

Open source document

Source excerpt

# OCCUPATIONAL HEALTH AND SAFETY CODE Index <table><tr><th></th><th>in definition of isolated work site, 1</th><th>hitch knots, 150.3</th></tr><tr><td></td><td>health care facility, 1, 291.3</td><td>See also personal fall arrest system (PFAS)</td></tr><tr><td></td><td>emergency transportation, 180</td><td>hitting See violence and harassment</td></tr><tr><td></td><td>first aid requirements, not to apply, 181(4)</td><td>hoists, 59-87</td></tr><tr><td></td><td>lasers, 291.3</td><td>defined</td></tr><tr><td></td><td>lifting and handling loads</td><td>cantilever hoists, 1</td></tr><tr><td></td><td>adapting heavy or awkward loads, 209</td><td>chimney hoist, 1</td></tr><tr><td></td><td>appropriate equipment, 209.1</td><td>hoist, 1</td></tr><tr><td></td><td>handling program, 209.2</td><td>material hoists, 1</td></tr><tr><td></td><td>work site design, 209.1</td><td>tower hoist, 1</td></tr><tr><td></td><td>Health Professions Act</td><td>A-frame safe practices, 75</td></tr><tr><td></td><td>in definition of nurse, 1</td><td>application of Code, 59</td></tr><tr><td></td><td>hearing See audiometric testing; noise</td><td>cantilever hoists, 76</td></tr><tr><td></td><td>hearing protection devices</td><td>certification by engineer</td></tr><tr><td></td><td>defined, 1</td><td>boom on tower hoist, 99</td></tr><tr><td></td><td>fit testing, 222</td><td>cantilever hoists, 76(a)</td></tr><tr><td></td><td>in noise management programs, 221(g)</td><td>not commercially manufactured, 60, 62</td></tr><tr><td></td><td>standards, 222</td><td>repairs and modifications, 65(3)(f), 73</td></tr><tr><td></td><td>training of workers, 221(f)</td><td>chimney hoists, 77-79</td></tr><tr><td></td><td>See also audiometric testing; noise; personal</td><td>equipment requirements, 77</td></tr><tr><td></td><td>protective equipment (PPE)</td><td>operator responsibilities, 78</td></tr><tr><td></td><td>Hearing Protection Devices - Performance, selection,</td><td>worker in lifting device, 79</td></tr><tr><td></td><…

[5] Lockout/Tagout Sample Forms: Evaluation, Procedures, and Permit

Page 9

Open source document

Source excerpt

# Equipment-Specific Hazardous Energy Control Evaluation and Certification (cont.) Enter name of your company here # Safety Permit for Hazardous Energy Control (Lockout/Tagout) Work Operations Date of work activity: <empty> Permit issued to: Authorized employee name: <empty> Title: <empty> Company name (if outside contractor): <empty> Contact number: <empty> Date/Time issued: <empty> Date/Time permit expires: <empty> Work activity: <empty> Machine/equipment description: <empty> Work location: <empty> Personal protective equipment (PPE), as required: (also circle specific types within the parentheses) [ ] Face shield [ ] Ear plugs [ ] Hard hat [ ] Safety glasses [ ] Ear muffs [ ] Hood (chemical, thermal) [ ] Safety goggles [ ] Suit (rubber, thermal, Tyvek) [ ] Safety harness & line [ ] Filtering facepiece/N95 [ ] Respirator (dust, vapor, combination, full-face, half-face) [ ] Gloves (thermal) [ ] Gloves (latex, neoprene, nitrile, PVC, rubber) [ ] Rubber boots [ ] Shoes (steel-toed, electrical safety, slip-resistant) [ ] Additional PPE required: <empty> Energy control devices, as required: (also circle applicable activities within the parentheses) [ ] Disconnect [ ] Blocks [ ] Accident prevention tags [ ] Valves (close, block, blind) [ ] Lock devices (individual, group) [ ] Grounding means [ ] Lines (bleeding, blanking/blinding) [ ] Other: <empty> Other safety considerations, as required: (also circle applicable items within the parentheses) [ ] Confined space (requires additional permit) [ ] Fire hazards (fire extinguisher, area free of combustibles) [ ] Restrict area (barricade, safety tape) [ ] Welding (sparks, shield arcs) [ ] Safe access (ladder, aerial device, scissor lift) [ ] Other: <empty> Approval: Signature: <empty> Print name/title (i.e., Safety Manager, Supervisor): <empty> Date: <empty> [ ] Job complete [ ] Job incomplete Notes: <empty> The authorized worker holds this permit during the work activity and returns it to the approver after wo…

[6] Occupational Health and Safety Code (Alberta Regulation 191/2021)

Page 407

Open source document

Source excerpt

# OCCUPATIONAL HEALTH AND SAFETY CODE Index <table><tr><th></th><th>documents</th><th>present until replaced or workers have left, 56(5)</th></tr><tr><td></td><td>code of practice, 44, 52(4)-(5)</td><td>records of workers in space, 56(4)</td></tr><tr><td></td><td>emergency response plan, 55</td><td>system for summoning assistance, 56(2)</td></tr><tr><td></td><td>entry permit system, 47, 50, 58</td><td>training, 56(2)</td></tr><tr><td></td><td>evacuation procedures, 53(4)</td><td>traffic hazards, 51</td></tr><tr><td></td><td>hazard assessment, 45, 52(3), 52(6), 58</td><td>training, 46, 53, 56(2)</td></tr><tr><td></td><td>inspection records, 48(3)</td><td>unauthorized entry, 50</td></tr><tr><td></td><td>inspections of equipment, 48(2)-(3), 58</td><td>ventilation, 53</td></tr><tr><td></td><td>retaining records, 58</td><td>water dangers, 49</td></tr><tr><td></td><td>training records, 46</td><td>Connecting components for personal fall-arrest</td></tr><tr><td></td><td>emergency equipment, 45, 46(3), 48(1), 48(2)</td><td>systems (PFAS) (CSA), 835(d)</td></tr><tr><td></td><td>emergency response plan, 2.2, 55, 56(2), 115-116</td><td>connectors</td></tr><tr><td></td><td>entry permit system, 47, 50, 58</td><td>standards for fall arrest system, 143(1)</td></tr><tr><td></td><td>evacuation procedures, 53(4)-(5), 55</td><td>constructed portable ladders See ladders</td></tr><tr><td></td><td>first aid, 46(3)(a)</td><td>construction</td></tr><tr><td></td><td>harmful substances, 49</td><td>first aid, high hazard work, 178, 181(1), Schedule 2,</td></tr><tr><td></td><td>hazard assessment, 45, 49, 52, 56, 58</td><td>Tables 3 and 7</td></tr><tr><td></td><td>hazardous energy, 49</td><td>Construction and Demolition Operations - Personnel</td></tr><tr><td></td><td>hoppers, safeguards, 316</td><td>and Debris Nets (ANSI), 320(1)(a)</td></tr><tr><td></td><td>inerting, 54</td><td>Construction and Test of Electric Cranes and Hoists</td></tr><tr><td></td><td>inspections and tests</td><td>(CSA), …

[7] OSH Enforcement Procedures | CFR 128D - Employer Payment for Personal Protective Equipment

Page 33

Open source document

Source excerpt

# TABLE XI-1.-OSHA STANDARDS THAT REQUIRE PPE (cont.) ## 29 CFR 1915, Shipyards (cont.) Federal Register/Vol. 72, No. 220/Thursday, November 15, 2007/Rules and Regulations [redacted postal code] # TABLE XI-1.-OSHA STANDARDS THAT REQUIRE PPE-Continued <table><tr><th>1915.35</th><th>Painting.</th></tr><tr><td>1915.51</td><td>Ventilation and protection in welding, cutting and heating.</td></tr><tr><td>1915.53</td><td>Welding, cutting and heating in way of preservative coatings.</td></tr><tr><td>1915.73</td><td>Guarding of deck openings and edges.</td></tr><tr><td>1915.77</td><td>Working surfaces.</td></tr><tr><td>1915.135</td><td>Powder actuated fastening tools.</td></tr><tr><td>1915.153</td><td>Eye and face protection.</td></tr><tr><td>1915.152</td><td>General requirements.</td></tr><tr><td>1915.154</td><td>Respiratory Protection.</td></tr><tr><td>1915.155</td><td>Head protection.</td></tr><tr><td>1915.156</td><td>Foot protection.</td></tr><tr><td>1915.157</td><td>Hand and body protection.</td></tr><tr><td>1915.158</td><td>Lifesaving equipment.</td></tr><tr><td>1915.159</td><td>Personal fall arrest systems (PFAS).</td></tr><tr><td>1915.160</td><td>Positioning device systems.</td></tr><tr><td>1915.504</td><td>Fire watches.</td></tr><tr><td>1915.505</td><td>Fire response.</td></tr><tr><td>1915.1001</td><td>Asbestos.</td></tr><tr><td>1915.1026</td><td>Chromium (VI).</td></tr><tr><td colspan="2">29 CFR 1917, Marine Terminals</td></tr><tr><td>1917.22</td><td>Hazardous cargo.</td></tr><tr><td>1917.23</td><td>Hazardous atmospheres and substances.</td></tr><tr><td>1917.25</td><td>Fumigants, pesticides, insecticides and hazardous waste.</td></tr><tr><td>1917.26</td><td>First aid and lifesaving facilities.</td></tr><tr><td>1917.49</td><td>Spouts, chutes, hoppers, bins, and associated equipment.</td></tr><tr><td>1917.73</td><td>Terminal facilities handling menhaden and similar species of fish.</td></tr><tr><td>1917.91</td><td>Eye and face protection.</td></tr><tr><td>1917.92…

[8] Personal Protective Equipment (PPE) Checklist

Page 1

Open source document

Source excerpt

# Personal Protective Equipment (PPE) Checklist <table><tr><th>General PPE Requirements</th><th>Yes</th><th>No</th><th>Comments</th></tr><tr><td>1. Has a hazard assessment to identify and control physical and health hazards been completed? If not, perform a hazard assessment.</td><td></td><td></td><td></td></tr><tr><td>2. Have engineering and/or administrative controls been applied prior to the use of PPE? If not, apply them first if applicable and appropriate.</td><td></td><td></td><td></td></tr><tr><td>3. Has appropriate PPE that matches the hazard been identified and provided to employees for use?</td><td></td><td></td><td></td></tr><tr><td>4. Has the effectiveness of the PPE program been reviewed, updated and evaluated periodically?</td><td></td><td></td><td></td></tr><tr><td>5. Have employees been trained on the use and care of the PPE?</td><td></td><td></td><td></td></tr><tr><td>6. Have employees been trained on the limitations of the PPE?</td><td></td><td></td><td></td></tr><tr><td>7. Is the PPE training documented and kept on file?</td><td></td><td></td><td></td></tr><tr><td>8. Are supervisors enforcing the use of required PPE?</td><td></td><td></td><td></td></tr><tr><td>9. Is PPE inspected regularly and properly maintained?</td><td></td><td></td><td></td></tr><tr><td>10. Is worn and damaged PPE removed from service and replaced?</td><td></td><td></td><td></td></tr><tr><td>11. When the following type of PPE is necessary, is the employer providing and paying for the PPE as stated by the OSHA standard 1910.132? Metatarsal foot protection - Rubber boots with steel toes Non-specialty-toe footwear (i.e. steel toe shoes/boots) if the employer does not permit it to be worn off the job site Non-prescriptive eye protection Prescriptive eyewear inserts/lenses for full face respirators Goggles and face shields Firefighting PPE (i.e. helmet, boots, gloves, full gear, proximity suits, etc.) Hard hats Hearing protection Welding PPE</td><td></td><td></td><td></td></tr></t…

[9] Personal Protective Equipment (PPE) Guide

Page 19

Open source document

Source excerpt

# Option 1 ## HANDS/ARMS Work activities, such as: [ ] baking [ ] material handling [ ] cooking [ ] sanding [ ] grinding [ ] sawing [ ] welding [ ] hammering [ ] working with glass [ ] using computers [ ] using knives [ ] dental and health care services [ ] other: <empty> Work-related exposure to: [ ] blood [ ] irritating chemicals [ ] tools or materials that could scrape, bruise, or cut [ ] extreme heat/cold [ ] other: <empty> Can hazard be eliminated without the use of PPE? Yes [ ] No [ ] If no, use: [ ] Gloves [ ] Chemical resistance [ ] Liquid/leak resistance [ ] Temperature resistance [ ] Abrasion/cut resistance [ ] Slip resistance [ ] Protective sleeves [ ] Other: <empty> FEET/LEGS Work activities, such as: [ ] building maintenance [ ] construction [ ] demolition [ ] food processing [ ] foundry work [ ] logging [ ] plumbing [ ] trenching [ ] use of highly flammable materials [ ] welding [ ] other: <empty> Work-related exposure to: [ ] explosive atmospheres [ ] explosives [ ] exposed electrical wiring or components [ ] heavy equipment [ ] slippery surfaces [ ] tools [ ] other: <empty> Can hazard be eliminated without the use of PPE? Yes [ ] No [ ] If no, use: [ ] Safety shoes or boots [ ] Toe protection [ ] Metatarsal protection [ ] Electrical protection [ ] Heat/cold protection [ ] Puncture resistance [ ] Chemical resistance [ ] Leggings or chaps [ ] Foot-Leg guards [ ] Other: <empty> BODY/SKIN Work activities such as: [ ] baking or frying [ ] battery charging [ ] dip tank operations [ ] fiberglass installation [ ] irritating chemicals [ ] sawing [ ] other: <empty> Work-related exposure to: [ ] chemical splashes [ ] extreme heat/cold [ ] sharp or rough edges [ ] other: <empty> Can hazard be eliminated without the use of PPE? Yes [ ] No [ ] If no, use: [ ] Vest, Jacket [ ] Coveralls, Body suit [ ] Raingear [ ] Apron [ ] Welding leathers [ ] Abrasion/cut resistance [ ] Other: <empty> 19

[10] Occupational Health and Safety Code (Alberta Regulation 191/2021)

Page 447

Open source document

Source excerpt

# OCCUPATIONAL HEALTH AND SAFETY CODE Index underground mines, self-rescue PPE, 702, 703.3, 703.4 vehicle traffic control, 194(2)-(5) workers duty to follow specifications, 12 duty to use, 3.2, 9(4)-(5), 228 PPE not to endanger worker, 228(3) training of, 228(1)(d) See also decontamination of workers; eye protection; headwear; life jackets; personal fall arrest system (PFAS); respiratory protective equipment; work positioning system Personal protective equipment against falls from a height - Connectors (CEN), 143(1), 835(a) Personal protective equipment against falls from a height - Descender devices (CEN), 146, 839(a) Personal protective equipment against falls from a height - Energy absorbers (CEN), 142.3(1) Personal protective equipment against falls from a height - Full body harnesses (CEN), 142(1), 795(1)(e), 834(b), 848(a) Personal protective equipment against falls from a height - Lanyards (CEN), 142.2(1), 819(2) Personal protective equipment against falls from a height - Part 2: Guided type fall arresters including a flexible anchor line (CEN), 144, 838(a) Personal protective equipment for prevention of falls from a height - Sit harnesses (CEN), 795(1)(b), 847(a) Personal protective equipment for the prevention of falls from a height - Low stretch kernmantle ropes (CEN), 147(1), 817(a) Personal protective equipment for work positioning and prevention of falls from a height - Belts for work positioning and restraint and work positioning lanyards (CEN), 142.1 (a), 148 personal vehicles for work purposes, 290.1 personnel baskets and man baskets chimney hoists, 77(g), 79 mobile cranes, standards, 88-88.1 for mobile cranes, standards, 88-88.1 personal fall arrest system, 75.1 suspended personnel baskets, 75.1 personnel hoists standards, 96 See also hoists persons, lifting defined in safe patient/client/resident handling, 1 See also lifting and handling loads Pest Control Products Act (Canada) WHMIS not to apply to products under, 395(5)(c) pet boarding and rai…

[11] Personal Protective Equipment (PPE) Hazard Assessment Tool

Page 10

Open source document

Source excerpt

# Hazard assessment worksheet: Hand protection (cont.) ## PPE required (cont.) OSHA Oregon OSHA Department of Consumer and Business Services # Hazard assessment worksheet: Respiratory protection Salem Central Office [redacted street address]. NE Salem, OR [redacted postal code] Phone: [redacted phone] Toll-free: [redacted phone] osha.oregon.gov Appropriate respirators are required when workers are exposed above permissible exposure limits (PEL) for specific air contaminates, listed in [redacted phone], Oregon Rules for Air Contaminants; see also 1910.134, Respiratory Protection. Work task: <empty> Date: <empty> ## Potential hazards <table><tr><th></th><th>No hazards requiring respiratory protection</th></tr><tr><td></td><td>Nuisance dust or mist</td></tr><tr><td></td><td>Welding fumes</td></tr><tr><td></td><td>Asbestos</td></tr><tr><td></td><td>Pesticides</td></tr><tr><td>ப:ப</td><td>Isocyanates</td></tr><tr><td></td><td>Paint spray</td></tr><tr><td></td><td>Organic vapors</td></tr><tr><td></td><td>Acid gases</td></tr><tr><td></td><td>Oxygen deficient, toxic, or IDLH atmosphere</td></tr><tr><td></td><td>Other hazard:</td></tr></table> ## PPE required <table><tr><th colspan="2">Air-purifying respirators</th></tr><tr><td></td><td>None required</td></tr><tr><td></td><td>Filtering face piece (dust mask)</td></tr><tr><td></td><td>Particulate-removing respirator</td></tr><tr><td></td><td>Gas-and-vapor-removing respirator</td></tr><tr><td></td><td>Combination aerosol filter, gas, or vapor-removing respirator</td></tr><tr><td></td><td>Powered air-purifying respirator</td></tr><tr><td colspan="2">Atmosphere-supplying respirators</td></tr><tr><td></td><td>None required</td></tr><tr><td></td><td>Supplied-air respirator</td></tr><tr><td></td><td>Self-contained breathing apparatus (SCBA)</td></tr><tr><td></td><td>Combination self-contained breathing apparatus and air-line respirator</td></tr><tr><td></td><td>Combination air-purifying and atmosphere-supplying respirato…

Related Q&A

Keep exploring.

Human questionUS

Write a safety checklist for Monthly inspection safety checklist for a cafe

Use a documented monthly cafe inspection that checks each area as Pass / Fail / N/A, records the hazard found, assigns a corrective action, names the responsible person, and tracks completion date. This aligns with inspection formats that include corrective action and completion fields, and with regulatory expectations

Read the thread
Human questionGeneral

Give me a audit for a construction site

Safety Audit Checklist for Construction Site Hazard Identification and Risk Assessment ====================================================================================== This checklist provides a framework for conducting safety audits on construction sites, focusing on hazard identification and risk assessment. It

Read the thread
Human questionUS

What should a HSE Manager inspect when visiting a customers site?

Here's a checklist for HSE Managers when visiting a customer site, incorporating elements from OSHA standards relevant to Texas [1]: *HSE Manager Customer Site Inspection Checklist** *Purpose:** To ensure compliance with safety regulations and promote a safe working environment at customer sites. *Instructions:**

Read the thread
Discussion thread

Add your experience.

Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.

New contributions are temporarily closed while the moderation queue is configured.

Community answers(0)

No community answers have been approved yet.

Comments on Rosie's answer(0)

No comments have been approved yet.

Ready to put operational safety to work?

Join 400K users across 150K sites already on SALUS.

Request a demo

No commitment · 30-minute personalized walkthrough