Skip to content
All safety questions
Asked by a personUnited Statesen-US

Write a safety checklist for Vehicle and heavy duty machine

A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.

Rosie's answer

Published by SALUS

A comprehensive safety checklist for vehicles and heavy-duty machinery should require a documented hazard-control program, competent and authorized operators, pre-use inspections, safe maintenance controls, PPE, and records that show defects are corrected before equipment is used. At minimum, the employer should maintain a written injury and illness prevention or equivalent safety program that identifies vehicle and equipment hazards, provides regular inspections, investigates incidents, and corrects hazardous conditions. Operators should be properly licensed where required and trained in the safe operation of the specific vehicle or machine they use. [1] [1] [9] [9]

Pre-operation inspection requirements:

  • Inspect each vehicle or machine at the beginning of each shift or work day before use.
  • Remove defective equipment from service until defects are repaired.
  • Check safety-critical items such as brakes, parking brake, steering, tires or wheels, horn, seat belts or operator restraints, lights, mirrors, controls, coupling devices, guards, alarms, windshield and wipers, and other safety devices.
  • For telehandlers, forklifts, and similar equipment, include visual and functional checks of hydraulics, cylinders, boom or mast, chains, forks or attachments, frame, tires, battery or fuel system, operator cab controls, horn, lights, steering, service brake, parking brake, reverse alarm, and any backup sensor or camera systems.
  • Verify labels, manuals, data plates, and warning decals are present and legible.

[1] [4] [6] [6] [3] [3] [8] Operator training and authorization requirements:

  • Allow only trained, authorized, and where applicable licensed operators to operate vehicles and heavy equipment.
  • Provide machine-specific training on controls, limitations, load handling, visibility limits, reversing, parking, refueling, and emergency procedures.
  • Ensure workers in training are directly supervised until they are competent.
  • Document operator training, evaluations, authorizations, and any required refresher training.

[1] [4] [9] [9] Lockout/tagout and maintenance safety requirements:

  • Before maintenance, inspection, cleaning, or repair, isolate hazardous energy and prevent unexpected movement or release of stored energy.
  • Lower blades, buckets, dump bodies, booms, forks, and other elevated components to the ground where possible; if they must remain raised, block or mechanically support them with a positive means of restraint.
  • Set parking brakes, chock wheels on inclines, stop the engine, remove the key, and verify isolation before work begins.
  • Use tire cages or equivalent protection for split-rim or locking-ring tire servicing, and allow only competent workers to perform tire service.
  • Do not bypass guards or protective devices during maintenance, and do not return equipment to service until repairs are complete and the machine is tested safe.

[4] [4] [4] [9] [9] [4] Hazard identification and incident prevention controls:

  • Identify site hazards before operation, including pedestrian traffic, blind spots, unstable ground, slopes, overhead power lines, overhead obstructions, weather, congestion, and reversing hazards.
  • Use traffic control measures such as warning signs, barricades, designated travel routes, exclusion zones, and flaggers or spotters where needed.
  • Require backup alarms or observers when rear visibility is obstructed.
  • Secure loads against displacement and ensure the machine is stable and not overloaded.
  • Investigate near misses, property damage, and injury incidents, then implement corrective actions and communicate lessons learned.

[1] [2] [4] [5] [5] [5] [2] Personal protective equipment requirements:

  • Require task-appropriate PPE based on the hazard assessment, typically including hard hat, high-visibility clothing, safety footwear, gloves, eye protection, hearing protection, and respiratory protection where dust, fumes, or exhaust exposures exist.
  • Inspect PPE regularly, ensure proper fit, and train workers on selection, use, adjustment, care, and replacement.
  • Where respirators are required, complete medical evaluations, fit testing, training, and recordkeeping before use.

[7] [7] [7] [7] [7] [11] Safe operating procedure requirements:

  • Require seat belt use whenever operating or riding in equipment equipped with restraints.
  • Do not allow riders on equipment unless the machine is specifically designed for passengers and has adequate seating.
  • Operate within posted and safe speeds, maintain full control, and keep equipment in gear where required.
  • Confirm horns, backup alarms, lights, brake lights, and warning devices are operable.
  • Use spotters when backing in congested, noisy, or obstructed areas.
  • Refuel only with the engine off and away from ignition sources; prohibit smoking in refueling areas.
  • Do not operate engines in enclosed areas without adequate ventilation.
  • Park safely by lowering attachments, setting the parking brake, shutting down, and securing against movement.

[2] [2] [2] [5] [5] [5] [5] [5] Protective structures, guards, and equipment configuration requirements:

  • Provide and maintain ROPS, FOPS, TOPS, overhead guards, cab shields, canopies, and other protective structures as required by the machine type and hazard exposure.
  • Inspect guards and protective structures daily for cracks, bends, looseness, or other damage.
  • Do not drill, weld, or otherwise modify certified ROPS/FOPS/TOPS structures unless approved by the manufacturer.
  • Ensure operator visibility is not impaired by accessories, loads, or installed equipment, and secure loose items in the cab so they do not become impact hazards.

[1] [4] [10] [10] [10] [12] [2] OSHA and regulatory compliance points to include in the checklist:

  • Reference applicable OSHA construction standards for motor vehicles and mechanized equipment, including 29 CFR 1926\.600, 1926\.601, 1926\.602, and equipment-specific rules.
  • Verify required brake systems, audible warning devices, backup alarms or observers, seat belts, inspection practices, and operator training are in place.
  • Where state plans or provincial rules apply, also verify compliance with local requirements for authorized operators, inspections, maintenance records, hazardous energy isolation, ROPS/FOPS standards, and seat belt use.
  • Use manufacturer operating manuals as part of the inspection and operating procedure requirements.

[4] [4] [4] [4] [4] [9] [3] Incident prevention documentation that should be required:

  • Daily or shift pre-use inspection forms with operator name, signature, date, equipment ID, hour meter, defects found, and repair status.
  • Maintenance and repair records showing defects were corrected before return to service.
  • Operator training, licensing, authorization, supervision, and refresher training records.
  • Hazard assessments, job safety analyses, traffic control plans, spotter assignments, and lockout/tagout or hazardous energy isolation records for maintenance work.
  • Incident, near-miss, and accident investigation reports with corrective actions and follow-up verification.
  • PPE training, respirator medical evaluations, fit tests, and inspection records where applicable.

[3] [3] [3] [8] [9] [7] In practice, the strongest checklist is one that does three things: it verifies the machine is safe before use, verifies the operator is competent and authorized, and creates records showing hazards, defects, maintenance controls, and incidents were identified and corrected. If you want, I can also convert this into a one-page audit checklist or a field inspection form. [1] [6]

12 source record(s)

Sources used for this answer

[1] Forklift Operator’s Daily Checklist

Page 1

Open source document

Source excerpt

# Forklift Operator's Daily Check List Check each item Before Start of Each Shift Date_____________ Check one: [ ] Gas/LGP/Diesel Truck [ ] Electric Sit-down [ ] Electric Stand-up [ ] Electric Pallet Truck Serial Number: <empty> Hour meter reading: <empty> Operator: <empty> Supervisor's OK: <empty> Let you supervisor and/or maintenance know of any problem. DO NOT OPERATE A FAULTY TRUCK. Your safety is at risk. Check boxes: ok [x] NG = needs attention, or repair – circle problem and comment * * (if equipped) <table><tr><th>OK</th><th>NG</th><th>Visual Check</th><th>Comment</th></tr><tr><td></td><td></td><td>Tires/wheels: wear, damage, nuts tight</td><td></td></tr><tr><td></td><td></td><td>Head/Tail/Working Lights: damage, mounting, operation</td><td></td></tr><tr><td></td><td></td><td>Gauges/Instruments: damage, operation</td><td></td></tr><tr><td></td><td></td><td>Operator Restraint: damage, mounting, operation, oily, dirty</td><td></td></tr><tr><td></td><td></td><td>Warning Decals/Operator's Manual: missing, not readable</td><td></td></tr><tr><td></td><td></td><td>Data Plate: not readable, missing</td><td></td></tr><tr><td></td><td></td><td>Overhead Guard: bent, cracked, loose, missing</td><td></td></tr><tr><td></td><td></td><td>Load Back Rest: bent cracked, loose, missing</td><td></td></tr><tr><td></td><td></td><td>Forks: bent, worn, stops OK</td><td></td></tr><tr><td></td><td></td><td>Engine Oil: level, dirty, leaks</td><td></td></tr><tr><td></td><td></td><td>Hydraulic Oil: level, dirty, leaks</td><td></td></tr><tr><td></td><td></td><td>Radiator: level, dirty, leaks</td><td></td></tr><tr><td></td><td></td><td>Fuel: levels, leaks</td><td></td></tr><tr><td></td><td></td><td>Battery: connections loose, charge, electrolyte low</td><td></td></tr><tr><td></td><td></td><td>Covers/Sheet metal: damaged, missing</td><td></td></tr><tr><td></td><td></td><td>Brakes: linkage, reservoir fluid level, leaks debris on floor</td><td></td></tr><tr><td></td><td></td><td>En…

[2] Occupational Health and Safety Code (Alberta Regulation 191/2021)

Page 449

Open source document

Source excerpt

# OCCUPATIONAL HEALTH AND SAFETY CODE Index entry restrictions, 258(3) precautions, 258(1) during worker transportation, 275(2) direct supervision, 256 documents inspection records, 260(5) operator's manual for ATV or snow vehicle, 281 procedures for rollover protection, 270(3) dumping block in mines, 542 elevated parts, 261 excavations, access and block, 459-460 exhaust gases not to enter enclosed body, 275(4) explosives flammable, combustible or explosive materials, 277-279 working around a misfire, 510.1 extending booms, ladders, 128 falling objects protective structures, 272-273 flammable, combustible or explosive materials, 277- 279 flying or projecting objects, protections, 269 forklift trucks, 283-284 fuel tank in cab, 274 guards and screens, 269 hazardous energy control isolation of hazardous energy, 212-215.3 manufacturer's specifications for isolation, 212 operation during control, 212(2) verification of isolation, 213 hazardous loads, 277 housekeeping, 256(3)(f), 275(2) inspection and maintenance by competent worker, 260(1) elevated parts, 261 hazards, 260(3) manufacturer's specifications, 260(2) records, 260(5) report to employer, 260(4) visual inspections, 257, 257.1, 267(2) lights, 264 maintenance, 260-261, 277 operator responsibilities, generally, 256 authorized operator, 256(1) full control of equipment, 256(3)(c) housekeeping, 256(3)(f) report on conditions, 256(3)(a) safe operation, 256(3)(b) seat belt use, 256(3)(d)-(e) starting engines, 262 unattended equipment, 263 visual inspection, 257, 257.1 pedestrian traffic, 259 refuelling, 279 dispensing flammable fuels, 279 ignition sources, distances, 279(1)(b), 279(2)(b) no smoking, distances, 279(1)(a), 279(2)(a) riding on loads, 276, 286(2) rollover protective structures (ROPS), 270-271 certification by engineer, 270(3) seatbelts and restraint systems, 271 standards, 270(2) when needed, 270(1) seats, 266(c) snow vehicles, 280-282 specifications and certifications falling objects protective structu…

[3] Telehandler - SJ1044 TH/THS & SJ1056 TH/THS (216202) - Operation Manual

Page 54

Open source document

Source excerpt

# Section 4 - Pre-operation (cont.) ## 4.3-14 Test Back-up Sensor/Camera with Monitor (If Equipped) (cont.) Section 4 - Pre-operation Operator's Checklist # Table 4.4 Operator's Checklist SKYJACK Serial Number: Model: Date: Hourmeter Reading: Time: # Operator's Checklist Operator's Name (Printed): Operator's Signature: Each item shall be inspected using the appropriate section of the Skyjack operating manual. As each item is inspected, check the appropriate box. P PASS F FAIL R REPAIRED N/A NOT APPLICABLE <table><tr><th></th><th>NAPFR</th><th></th><th></th><th></th></tr><tr><td colspan="5">Visual and Daily Maintenance Inspections</td></tr><tr><td>Labels</td><td></td><td></td><td></td><td></td></tr><tr><td>Electrical</td><td></td><td></td><td></td><td></td></tr><tr><td>Hydraulic</td><td></td><td></td><td></td><td></td></tr><tr><td>Cylinders</td><td></td><td></td><td></td><td></td></tr><tr><td>Mirrors</td><td></td><td></td><td></td><td></td></tr><tr><td>Frame</td><td></td><td></td><td></td><td></td></tr><tr><td>Wheel/Tire Assembly</td><td></td><td></td><td></td><td></td></tr><tr><td>Air-filled Tires</td><td></td><td></td><td></td><td></td></tr><tr><td>Foam-filled Tires</td><td></td><td></td><td></td><td></td></tr><tr><td>Drive Axles</td><td></td><td></td><td></td><td></td></tr><tr><td>Steer Cylinder</td><td></td><td></td><td></td><td></td></tr><tr><td>Battery</td><td></td><td></td><td></td><td></td></tr><tr><td>Outriggers</td><td></td><td></td><td></td><td></td></tr><tr><td>Engine Intake Air Filter</td><td></td><td></td><td></td><td></td></tr><tr><td>Fuel Tank</td><td></td><td></td><td></td><td></td></tr><tr><td>Fuel Leaks</td><td></td><td></td><td></td><td></td></tr><tr><td>DEF Tank</td><td></td><td></td><td></td><td></td></tr><tr><td>Hydraulic Oil Tank</td><td></td><td></td><td></td><td></td></tr><tr><td>Hydraulic Oil</td><td></td><td></td><td></td><td></td></tr><tr><td>Engine Compartment</td><td></td><td></td><td></td><td></td></tr><tr><td>Engin…

[4] CAT CS10 GC, CS11 GC, CS12 GC Vibratory Soil Compactor Operation and Maintenance Manual

Page 29

Open source document

Source excerpt

# Before Starting Engine (cont.) ## Operator Station (cont.) M0085517-07 29 Safety Section Guards i07746359 # Guards (Operator Protection) SMCS Code: 7150 There are different types of guards that are used to protect the operator. The machine and the machine application determine the type of guard that should be used. A daily inspection of the guards is required in order to check for structures that are bent, cracked, or loose. Never operate a machine with a damaged structure. The operator becomes exposed to a hazardous situation if the machine is used improperly or if poor operating techniques are used. This situation can occur even though a machine is equipped with an appropriate protective guard. Follow the established operating procedures that are recommended for your machine. ## Rollover Protective Structure (ROPS), Falling Object Protective Structure (FOPS) or Tip Over Protection Structure (TOPS) The ROPS/FOPS Structure (if equipped) on your machine is specifically designed, tested and certified for that machine. Any alteration or any modification to the ROPS/FOPS Structure could weaken the structure. This places the operator into an unprotected environment. Modifications or attachments that cause the machine to exceed the weight that is stamped on the certification plate also place the operator into an unprotected environment. Excessive weight may inhibit the brake performance, the steering performance and the ROPS. The protection that is offered by the ROPS/FOPS Structure will be impaired if the ROPS/FOPS Structure has structural damage. Damage to the structure can be caused by an overturn, a falling object, a collision, etc. Do not mount items (fire extinguishers, first aid kits, work lights, etc) by welding brackets to the ROPS/ FOPS Structure or by drilling holes in the ROPS/ FOPS Structure. Welding brackets or drilling holes in the ROPS/FOPS Structures can weaken the structures. Consult your Cat dealer for mounting guidelines. The Tip Over P…

[5] Vehicles and Heavy Equipment Training Guide

Page 2

Open source document

Source excerpt

## ASK THE CREW THESE QUESTIONS: (cont.) • Mirrors • Steering • Operating controls • Leaking fluids • Headlights, taillights, brake lights, and turn signals - Seat belts • Horn and back-up alarm (loud enough to be heard 200 feet away) • Roll-over protection structure (ROPS) • Cab shields or canopies on haulage vehicles. 3. What are some safety rules to follow when operating any type of vehicle? • Wear a seat belt when operating any type of vehicle, whether it's a truck, bulldozer, loader, or grader. • Don't exceed the speed limit for the area. • Don't allow riders unless the vehicle is designed for them. • Refuel only when the vehicle is turned off and there are no sources of ignition nearby. NO SMOKING signs should be posted in refueling areas. . Don't run the engine in an enclosed area unless there is enough ventilation. 4. Before you move heavy equipment, what safety measures should you take? • Make sure there are warning signs, barricades, or flaggers to keep people out of the area. • Make sure you have a spotter to guide you when necessary. • Be aware of overhead obstructions, like power lines or trees. • If you don't have a clear view, walk around the vehicle to check for obstructions. • Make sure your vehicle is not overloaded. • Make sure any load you are carrying is secured and stable. 5. How far from a high voltage line must you keep a boom, crane, or lifting equipment? Who is in danger if the equipment contacts the line? • Keep all equipment at least 10 feet from high voltage lines that carry 50,000 volts or less. The clearance distance is more if the line carries higher voltage. • Everyone nearby is in danger if equipment contacts the line—not just the operator. (High Voltage Lines are covered in more detail in a separate Training Guide.) California Tailgate Training Vehicles and Heavy Equipment-Page 2

[6] Personal Protective Equipment (PPE) Checklist

Page 3

Open source document

Source excerpt

# Personal Protective Equipment (PPE) Checklist (cont.) <table><tr><th>29. Have medical evaluations been conducted for employees required to wear a respirator?</th><th></th><th></th></tr><tr><td>30. Have employees been fit tested?</td><td></td><td></td></tr><tr><td>31. Has air quality monitoring been conducted by a qualified industrial hygienist?</td><td></td><td></td></tr><tr><td>32. Have employees been trained on the written program and how to use and care for the respirators?</td><td></td><td></td></tr><tr><td>33. Have all training and fit test results been documented and kept on file?</td><td></td><td></td></tr><tr><td>34. Is the face piece clean?</td><td></td><td></td></tr><tr><td>35. Does the exhalation valve allow air to exit mask and not enter?</td><td></td><td></td></tr><tr><td>36. Is the regulator functioning properly?</td><td></td><td></td></tr><tr><td>37. Are the buckles, back plate and straps in good condition?</td><td></td><td></td></tr><tr><td>38. Is the pressure hose in working order?</td><td></td><td></td></tr><tr><td>39. Are the pressure cylinder and all knobs and gauges in good condition and working properly?</td><td></td><td></td></tr><tr><td>40. Are there any air leaks?</td><td></td><td></td></tr><tr><td>41. Is there any visible damage to any part of the mask/respirator, hoses or cylinder?</td><td></td><td></td></tr><tr><td>42. Is the filter or cartridge up-to-date, clean and free of any deterioration/damage?</td><td></td><td></td></tr><tr><td>43. Is the air cylinder fully charged?</td><td></td><td></td></tr><tr><td>Head Protection (N/A )</td><td>Yes No</td><td>Comments</td></tr><tr><td>44. Have employees been trained on how to select, use, adjust, wear and care for their head protection?</td><td></td><td></td></tr><tr><td>45. Is the head protection clean and in good condition?</td><td></td><td></td></tr><tr><td>46. Is the head protection adjusted properly to fit the wearer's head?</td><td></td><td></td></tr><tr><td>47. Are worn straps replace…

[7] Vehicles & Heavy Equipment Checklist

Page 2

Open source document

Source excerpt

# SAFETY WALKAROUND CHECKLIST VEHICLES & HEAVY EQUIPMENT (cont.) ## INSPECTION AND SAFETY EQUIPMENT (cont.) NOTES - Every vehicle and piece of heavy equipment with a cab has an intact windshield and powered windshield wipers. Where needed, there is operable defogging or defrosting equipment. [1591(a) and 1597(d)] - Equipment and accessories installed on haulage vehicles do not impair the driver's vision to the front or sides. [1591(b)] - Every vehicle and piece of heavy equipment has two operating headlights and two operating taillights when visibility conditions warrant. [1591(g) and 1597(b)] - Every vehicle and piece of heavy equipment has working brake lights. [1591 and 1597(c)] - Dump trucks that tilt to release their load have a visible or audible warning when the elevating mechanism is activated. [1591(k)] - Loads on vehicles are secured against displacement. [1593(f)] - Drivers operating loaders have adequate visibility, and the equipment is stable. [1593(j)] - On piledrivers, safety chains on compression hose fittings are in place and in working order, to prevent thrashing if disconnected. [1600(c)] ## WORK PRACTICES - The employer requires the use of seat belts when operating or riding in vehicles or heavy equipment. [1597(h)] - Operators do not exceed safe or posted speed limits. [1590(c)(2) and 1593(a)] - Haulage vehicles have a cab shield or canopy to protect the driver from falling materials. [1591(e)] - Wherever feasible, a spotter is used to help operators back up vehicles and heavy equipment. The spotter stands well away from the operation, in clear view of the operator. Spotters are required in noisy or congested areas, whenever backward motion is hazardous, and whenever the operator's vision to the back is obstructed. [1592(a)] - Workers do not ride on equipment not designed for riders, including hoist platforms, buckets, or on loads. [1605.9 and 1605.10] - Vehicles used to transport workers have seats firmly secured, and have eno…

[8] Vehicles & Heavy Equipment Checklist

Page 1

Open source document

Source excerpt

# SAFETY WALKAROUND CHECKLIST VEHICLES & HEAVY EQUIPMENT 2001 Date Prepared: Project Name/No: By: Location: • Check the box if the statement is true. • Fill in the blanks where the - appears. • Citations in brackets are from Title 8 of the California Administrative Code. ## HAZARD IDENTIFICATION AND WORKER TRAINING NOTES - The company has a written Injury and Illness Prevention Program (IIPP) that meets all Cal/OSHA requirements. It includes identification of hazards on the site involving vehicles and heavy equipment, as well as regular inspections, accident investigation, and correction of hazardous conditions. [1509] - All drivers are properly licensed, and have been trained in the proper and safe operation of vehicles and equipment. [3664(a)(1) and 5006(a)] ## INSPECTION AND SAFETY EQUIPMENT - All vehicles and heavy equipment are visually inspected at the beginning of each work day for any malfunctions that could affect safe operation. All defects are corrected before the equipment is placed in service. [1593(d), 1597(j), and 3664(a)(7)] - Every haulage vehicle and piece of heavy equipment has a working back-up alarm that can be heard 200 feet away. [1592(a) and (b)] - Seat belts in good working order are provided on all vehicles and heavy equipment. [1596(g) and 1597(g)] - Roll-over protection structures (ROPS) are provided on vehicles and heavy equipment (including scrapers, tractors, loaders, bulldozers, carryalls, trucks, etc.). [1596(a)] California Tailgate Training Vehicles and Heavy Equipment-Page 1

[9] CAT 336 GC Excavator Operation and Maintenance Manual

Page 48

Open source document

Source excerpt

# High Pressure Fuel Lines (cont.) ## Guidelines for Reducing Vibration Levels on Earthmoving Equipment (cont.) 48 Safety Section Operator Station M0110641-02 f. Minimize any shocks and impacts during sports and leisure activities. ## Sources The vibration information and the calculation procedure are based on "ISO/TR [redacted postal code] Mechanical Vibration Guideline for the assessment of exposure to whole body vibration of ride on operated earthmoving machines". Harmonized data is measured by international institutes, organizations, and manufacturers. This literature provides information about assessing the whole body vibration exposure of operators of earthmoving equipment. The method is based on measured vibration emission under real working conditions for all machines. Check the original directive. This document summarizes part of the content of the applicable law. This document is not meant to substitute the original sources. Other parts of these documents are based on information from the United Kingdom Health and Safety Executive. Refer to Operation and Maintenance Manual, SEBU8257, "The European Union Physical Agents (Vibration) Directive 2002/44/EC" for more information about vibration. Consult your local Cat Ⓡ dealer for more information about machine features that minimize vibration levels. Consult your local Cat dealer about safe machine operation. Use the following web site to find your local dealer: Caterpillar, Inc. www.cat.com i07746362 ## Operator Station SMCS Code: 7300; 7301; 7325 Any modifications to the inside of the operator station should not project into the operator space or into the space for the companion seat (if equipped). The addition of a radio, fire extinguisher, and other equipment must be installed so that the defined operator space and the space for the companion seat (if equipped) is maintained. Any item that is brought into the cab should not project into the defined operator space or the space for the compan…

[10] CAT 335 Excavator Operation and Maintenance Manual

Page 50

Open source document

Source excerpt

# High Pressure Fuel Lines (cont.) ## Guidelines for Reducing Vibration Levels on Earthmoving Equipment (cont.) 50 Safety Section Operator Station M0106778-03 f. Minimize any shocks and impacts during sports and leisure activities. ## Sources The vibration information and the calculation procedure is based on "ISO/TR [redacted postal code] Mechanical Vibration Guideline for the assessment of exposure to whole body vibration of ride on operated earthmoving machines". Harmonized data is measured by international institutes, organizations, and manufacturers. This literature provides information about assessing the whole body vibration exposure of operators of earthmoving equipment. The method is based on measured vibration emission under real working conditions for all machines. You should check the original directive. This document summarizes part of the content of the applicable law. This document is not meant to substitute the original sources. Other parts of these documents are based on information from the United Kingdom Health and Safety Executive. Refer to Operation and Maintenance Manual, SEBU8257 for more information about vibration. Consult your local Caterpillar dealer for more information about machine features that minimize vibration levels. Consult your local Caterpillar dealer about safe machine operation. Use the following web site to find your local dealer: Caterpillar, Inc. www.cat.com i07746362 ## Operator Station SMCS Code: 7300; 7301; 7325 Any modifications to the inside of the operator station should not project into the operator space or into the space for the companion seat (if equipped). The addition of a radio, fire extinguisher, and other equipment must be installed so that the defined operator space and the space for the companion seat (if equipped) is maintained. Any item that is brought into the cab should not project into the defined operator space or the space for the companion seat (if equipped). A lunch box or other lo…

[11] Occupational Safety and Health (Title 803, Chapter 002)

Page 3

Open source document

Source excerpt

# Technical Amendment November 10, 2022 EDUCATION AND LABOR CABINET (Technical Amendment) (cont.) - lowering of the body while maintenance or inspection work is being done. (m) Operating levers controlling hoisting or dumping devices on haulage bodies shall be equipped with a latch or other device that prevents accidental starting or tripping of the mechanism. (n) Trip handles for tailgates of dump trucks shall be so arranged that, in dumping, the operator will be in the clear. (o) 1. Each employer shall assure the following parts, equipment, and accessories are in safe operating condition and free of apparent damage that could cause failure while in use: a. Service brakes, including trailer brake connections; b. Parking system brake; c. Brakes; d. Tires; e. Horn; f. Steering mechanism; g. Coupling devices; h. Seat belts; i. Operating controls; and j. Safety devices. 2. All defects shall be corrected before the vehicle is placed in service. 3. These requirements shall also apply to equipment such as lights, reflectors, windshield wipers, defrosters, and fire extinguishers. (3) Material handling equipment. (a) General. The requirements of this subsection shall apply to scrapers, loaders, crawler or wheel tractors, bulldozers, off-highway trucks, graders, agricultural and industrial tractors, and similar equipment. (b) Seating and seat belts. 1. Each employer shall insure safe seating with seat belts on all equipment covered by this section, and shall meet the requirement of J386, Society of Automotive Engineers Handbook, 1986, Operator Restraint Systems for Off-road Work Machines. 2. Seat belts for agricultural and light industrial tractors shall meet the seat belt requirements of Society of Automotive Engineers J1194, Society of Automotive Engineers Handbook, 1986, Rollover Protective Structures (ROPS) for Wheeled Agricultural Tractors. (c) Seat belts need not be provided for equipment designed on…

[12] Construction Industry Checklist

Page 17

Open source document

Source excerpt

# Scaffolding (cont.) ## Motor Vehicles, Mechanized Equipment and Marine Operations (cont.) <table><tr><th>Are safety tire racks, cages, or equivalent protective devices provided and used when inflating, mounting or dismounting tires installed on split rims or locking rings? 1926.600(a)(2)</th><th></th></tr><tr><td>Are bulldozer and scraper blades, dump bodies, etc., fully lowered or blocked when being repaired or not in use? 1926.600(a)(3)(i)</td><td></td></tr><tr><td>Are parking brakes set on parked equipment, and are wheels chocked when parked on an incline? 1926.600(a)(3)(ii)</td><td></td></tr><tr><td>Do these vehicles have a service brake system, emergency brake system, and parking brake system in operable condition? 1926.601(b)(1)</td><td></td></tr><tr><td>Are all vehicles equipped with an audible warning device in operable condition at the operator's station? 1926.601(b)(3)</td><td></td></tr><tr><td>Do all vehicles with an obstructed view to the rear have a backup alarm or are they always used with an observer? 1926.601(b)(4)</td><td></td></tr><tr><td>Do all vehicles have seat belts and are their use required? 1926.601(b)(9)</td><td></td></tr><tr><td>Are trucks with dump bodies (beds) equipped with a positive means of support, permanently attached, and capable of being locked in position to prevent accidental lowering of the body (bed of truck) while maintenance or inspection work is being done? 1926.601(b)(10)</td><td></td></tr><tr><td>Are operating levers on dump trucks equipped with latches? 1926.601(b)(11)</td><td></td></tr><tr><td>Are tail gate handles on dump trucks arranged to keep operator clear? 1926.601(b)(12)</td><td></td></tr><tr><td>Are vehicles in use inspected at the beginning of each shift to assure that all parts, equipment, and accessories affecting safety operations are free of defects? 1926.601(b)(14)</td><td></td></tr><tr><td>Material handling equipment: Are seat belts provided on all earth-moving equipment except those not equipped wit…

Related Q&A

Keep exploring.

Human questionGeneral

Generate a sheet for grounding

Safe Work Procedure: Grounding Document Number: [SWP-NUMBER] Revision Date: [DATE] Next Review Date: [NEXT REVIEW DATE] Department: [DEPARTMENT NAME] 1. Scope This Safe Work Procedure (SWP) outlines the necessary steps and safety precautions for performing grounding tasks. It applies to all workers involved in

Read the thread
Human questionGeneral

gas piping in trenches

Gas Piping Installation in Trenches: Safety Regulations ======================================================= *Date:** 2025-10-10 *Duration:** \[DURATION] minutes *Presenter:** \[PRESENTER NAME] *Location:** \[LOCATION] Objective To understand and apply safety regulations for gas piping installation in trenches

Read the thread
Human questionUS

No touch tools

Non-Contact Tool Safety ======================== *Date:** 2025-08-25 *Duration:** \[DURATION] minutes *Presenter:** \[PRESENTER NAME] *Location:** \[LOCATION] Objective The objective of this toolbox talk is to provide employees with the knowledge and skills necessary to safely use non-contact tools, thereby reducing

Read the thread
Human questionGeneral

Write a toolbox talk on TEsting of Relay

Safe Testing Procedures and Risk Assessment for Protective Relays ================================================================= *Date:** 2026-02-19 *Duration:** \[DURATION] minutes *Presenter:** \[PRESENTER NAME] *Location:** \[LOCATION] Objective To ensure all personnel understand and follow safe testing

Read the thread
Human questionGeneral

Write a risk assessment for Partial colour blindness for electrical apprentice risks

Risk Assessment for Electrical Apprentice with Partial Colour Blindness ======================================================================= *Assessment Date:** \[DATE] *Assessor:** \[ASSESSOR NAME] *Department/Area:** \[DEPARTMENT/AREA] *Review Date:** \[REVIEW DATE] 1\. Assessment Scope This assessment covers

Read the thread
Human questionUS

Safety Data Sheets (SDS)

Safety Data Sheets (SDS) ======================== *Date:** 2025-10-13 *Duration:** \[DURATION] minutes *Presenter:** \[PRESENTER NAME] *Location:** \[LOCATION] Objective To understand where to find Safety Data Sheets (SDS) for hazardous chemicals and materials and how to use the information within them to ensure safety

Read the thread
Discussion thread

Add your experience.

Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.

New contributions are temporarily closed while the moderation queue is configured.

Community answers(0)

No community answers have been approved yet.

Comments on Rosie's answer(0)

No comments have been approved yet.

Ready to put operational safety to work?

Join 400K users across 150K sites already on SALUS.

Request a demo

No commitment · 30-minute personalized walkthrough