Skip to content
All safety questions
Asked by a personUnited Statesen-US

Write a toolbox talk on Housekeeping in the workshop

A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.

Rosie's answer

Published by SALUS

A workshop housekeeping toolbox talk should emphasize that good housekeeping is a core safety practice, not just cleaning. Housekeeping means keeping work areas clean, orderly, sanitary, dry, and free of hazards so employees can work safely and move without obstruction. Poor housekeeping is a leading cause of injuries because it creates slip, trip, fall, struck-by, cut, puncture, and fire hazards. It should be treated as a continuous part of the job throughout the shift, with every employee responsible for maintaining standards. [1] [2] [1]

Key good housekeeping practices:

  • Clean as work progresses, not only at the end of the shift.
  • Pick up trash, scrap, and debris promptly and place it in proper containers.
  • Store tools, equipment, PPE, and materials neatly in designated areas when not in use.
  • Keep floors, benches, work surfaces, aisles, stairs, and passageways dry, clean, well lit, and free of obstructions.
  • Minimize dust during sweeping or cleaning.
  • Repair or report loose flooring, broken walking surfaces, leaks, poor lighting, and other conditions that can create hazards.
  • Return unused materials to storage and remove buildup of garbage before it accumulates.

[1] [10] [2] [6] Slip, trip, and fall prevention:

  • Keep walking and working areas clear of clutter, debris, boxes, loose materials, and misplaced tools.
  • Clean up spills, water, oil, grease, mud, and other slippery substances immediately; mark wet areas until they are safe.
  • Keep cords, hoses, cables, and welding leads out of walkways; if they must cross a path, cover, secure, tape down, or route overhead where appropriate.
  • Maintain stairs and stairwells clear, well lit, and in good repair; use handrails and do not carry loads that block your view.
  • Inspect for holes, uneven surfaces, loose mats, damaged flooring, and poor lighting, and correct or barricade hazards promptly.
  • Wear footwear suitable for the work environment, including slip-resistant soles where needed.

[4] [11] [9] [7] Safe storage of tools and materials:

  • Store materials only in designated storage areas and in a way that does not create a hazard.
  • Stack boxes, pallets, and materials in an orderly, stable manner so they cannot topple, slide, or collapse.
  • Keep stored materials away from walkways, doors, exits, stairs, floor openings, roof edges, excavations, trenches, and overhead power lines.
  • Do not store anything in stairwells or in front of emergency equipment.
  • Return tools to gang boxes, tool rooms, racks, cabinets, or other designated locations after use.
  • Store chemicals, gases, combustibles, and flammables in approved containers and cabinets, separated from ignition sources and incompatible materials.

[1] [4] [3] [10] [8] Waste disposal and fire hazard control:

  • Provide enough waste containers and empty them regularly.
  • Use separate approved containers for trash, scrap, oily rags, used rags, hazardous waste, and flammable waste.
  • Dispose of combustibles and flammables properly and promptly.
  • Keep rubbish, sawdust, packaging, and flammable debris away from welding, cutting, heaters, electrical equipment, and other ignition sources.
  • Never throw materials from one level to another; use containers or enclosed chutes where needed.
  • Ensure chemical containers are labeled and stored in designated areas.

[1] [2] [1] [3] Access and egress:

  • Keep all exits, aisles, passageways, stairs, ramps, and doorways clear at all times.
  • Maintain free access to fire alarm boxes, fire extinguishers, first aid stations, and other emergency equipment.
  • Clearly mark aisles and exits and ensure exit lighting is functional.
  • Do not block travel paths with pallets, skids, boxes, cords, hoses, or stored materials.
  • Keep stairwell doors closed where required and do not use stairwells for storage.

[1] [5] [2] Practical inspection checklist for supervisors and crews:

  • Are floors clean, dry, and free of oil, grease, water, scrap, and loose materials?
  • Are wet floor or slippery area signs used where needed?
  • Are cords, hoses, boxes, pallets, and loose flooring removed from walkways?
  • Are aisles, stairs, landings, and exits unobstructed, marked, and adequately lighted?
  • Are stairways free of storage and debris, and are steps in good repair?
  • Are flammables in approved cabinets or containers?
  • Are boxes and pallets stacked neatly and safely?
  • Are storage areas marked, and are materials placed so they do not interfere with workers or material flow?
  • Are tools and equipment stored in designated areas when not in use?
  • Are leaks identified, repaired, and cleaned up?
  • Is trash collected in proper containers and removed regularly?
  • Are separate containers provided for oily rags, hazardous waste, and flammable waste?
  • Are chemical containers labeled and stored correctly?
  • Has the housekeeping policy been reviewed, and do employees understand storage and material-handling procedures?

[5] [5] [6] Employee responsibilities:

  • Keep your own work area clean and correct housekeeping issues as you create them.
  • Pick up trip hazards, scrap, and debris immediately.
  • Put tools, cords, hoses, and materials away after use.
  • Report damaged floors, leaks, poor lighting, blocked exits, missing signs, and unsafe storage conditions right away.
  • Follow waste segregation and disposal rules.
  • Do not leave hazards for the next shift; housekeeping is everyone's job, not only the labor crew or janitorial staff.

[1] [10] [10] For OSHA compliance, the workshop should align its housekeeping program with OSHA construction housekeeping requirements in 29 CFR 1926\.25, which is specifically cited in the source material. In practice, that means keeping places of employment, passageways, storerooms, and service rooms clean and orderly; removing scrap and debris regularly; and storing materials safely so they do not obstruct exits or create hazards. Related OSHA expectations reflected in the source documents also include keeping emergency exits clear, controlling slip and trip hazards, and storing flammables properly. A compliant program should include routine inspections, prompt correction of hazards, employee training, and documented toolbox talks or safety meetings. [2] [1] [12]

A simple closing message for the toolbox talk is: Good housekeeping prevents injuries, fires, and delays. If you drop it, pick it up. If you spill it, clean it. If you move it, store it safely. If you see a hazard, fix it or report it immediately. [3] [11]

12 source record(s)

Sources used for this answer

[1] Housekeeping Inspection – Safety Checklist

Page 1

Open source document

Source excerpt

# Housekeeping Inspection - Safety Checklist <table><tr><th>Floors</th><th>Yes</th><th>No</th><th>N/A</th><th>Comments &amp; Action Needed</th><th>Completed Date</th></tr><tr><td>1. Are floors clean?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>2. Are the floor and work area congested?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>3. Are floors free of liquids?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>4. Do the floors need an anti-slip covering?</td><td></td><td>ப</td><td></td><td></td><td></td></tr><tr><td>5. Are signs in use to warn of slippery areas and wet floors?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>6. Is the work area free of tripping hazards such as cords, boxes, loose flooring, etc.?</td><td></td><td>ㅁ</td><td></td><td></td><td></td></tr><tr><td>7. Are used/unwanted materials lying on the floor?</td><td></td><td>ㅁ</td><td></td><td></td><td></td></tr><tr><td>Aisles &amp; Stairways</td><td>Yes 6</td><td>2 No</td><td>N/A</td><td>Comments &amp; Action Needed</td><td>Completed Date</td></tr><tr><td>8. Are aisles and stairways unobstructed and clearly marked?</td><td>ㅁㅁ</td><td> </td><td> </td><td></td><td></td></tr><tr><td>9. Are pallets, skids and boxes out of the aisles?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>10. Are the aisles and stairways properly lighted?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>11. Are stairways and landings free of storage?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>12. Are stairways and aisles clear of debris and liquids?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>13. Are steps free of defects and treads in good repair?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>14. Are aisles and passageways kept clean?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>Exits</td><td>Yes</td><td>No</td><td>N/A</td><td>Comments &amp; Action Needed</td><td>Completed …

[2] Toolbox Talk: Housekeeping

Page 1

Open source document

Source excerpt

# HOUSEKEEPING Last Review: 08/01/2025 Date Posted: 05/13/2025 # Housekeeping Maintaining a clean and tidy work area is a crucial practice on construction sites. Every individual working on the job site plays an essential role in ensuring good housekeeping. It refers to a workplace that is free from hazards and is organized and clutter-free. Good housekeeping is an integral part of daily work activities and plays a vital role in ensuring a safe working environment. All employees at all levels are responsible for maintaining good housekeeping standards, and it is an ongoing process that everyone must contribute to. ## HAZARDS OF POOR HOUSEKEEPING According to the Division of Occupational Safety and Health (DOSH), poor housekeeping is a leading cause of workplace accidents and injuries. A construction site with poor housekeeping can pose several hazards and risks to workers. When tools and materials are left lying around, it can create tripping hazards that can cause slips, trips, and falls. Clutter and debris can also obstruct walkways, causing workers to bump into objects, resulting in cuts, bruises, and other injuries. Good job site housekeeping is not just about cleanliness; it is a fundamental element for job site accident and fire prevention. It requires attention to detail, such as job site layout, internal job site travel routes, identification of potential hazards, and ensuring adequate storage areas and waste disposal areas. Poor housekeeping be a cause of accidents, such as: the can • Tripping over loose objects on floors, stairs, and platforms. - Being struck by falling objects. - Slipping on wet, oily, or dirty surfaces. - Striking against projecting, poorly stacked items, or misplaced materials. - Cutting, puncturing, or tearing the skin of hands or other parts of the body on projecting nails, wire, or steel strapping. ## HAZARD PREVENTION To avoid workplace hazards, maintain good housekeeping practices throughout the workday. Regular…

[3] Housekeeping Checklist

Page 1

Open source document

Source excerpt

# SAFETY WALKAROUND CHECKLIST HOUSEKEEPING 2001 Date Prepared: Project Name/No: By: Location: • Check the box if the statement is true. - Citations in brackets are from Title 8 of the California Administrative Code. ## HAZARD IDENTIFICATION, REMOVAL, AND CLEANUP NOTES - The company has a written Injury and Illness Prevention Program (IIPP) that meets all Cal/OSHA requirements. It includes identification of hazardous housekeeping problems on the site, regular inspections, accident investigation, and correction of hazardous conditions. [1509] - Debris is kept cleared from work surfaces, passages, and stairs. [1513(a)] - Ground within 6 feet of a building under construction is free of irregularities. [1513(b)] - Storage areas and walkways are reasonably free of dangerous depressions, obstructions, and debris. [1513(c)] - All walking and working surfaces are reasonably dry and free from grease or oil. [3273(a)] - Spills of oil, grease, and other liquids are removed at once, or covered with sand or other absorbent material until cleaned up. [3273(a)] - Sufficient waste or trash containers are provided, used and emptied when appropriate. [1513(f)] - Workers wear heavy gloves and heavy soled or safety shoes when handling scrap material. [1520 and 3385] - All walking and working surfaces are free of protruding nails. [1513(a)] - Nails or fasteners are removed when opening crates, cartons, kegs, or when stripping small forms. - Nails are bent down or removed before scrap material is discarded. California Tailgate Training Housekeeping-Page 1

[4] Preventing Slips, Trips, and Falls

Page 1

Open source document

Source excerpt

WORK SAFE KENTUCKY Free safety resources provided by KEMI HOME SAFETY RESOURCES SAFETY TRAINING SAFETY BLOG ABOUT KEMI CONTACT US O # Preventing Slips, Trips, and Falls ## Print a Sign-In Sheet | Spanish Version • According to the U.S. Department of Labor, slips, trips, and falls are the most common occupational accidents. • Many falls can be prevented with general safety precautions. • The two main causes of slips, trips, and falls are environmental conditions and human factors. CAUTION A FLOOR - • A slip occurs when there is too little traction, or friction, between the shoe and walking surface. • A trip occurs when a person's foot contacts an object in the way or drops to a lower level unexpectedly, causing the person to be thrown off-balance. • A fall occurs when a person is too far off-balance. ## The main causes of slips include: • Spills of liquids and other debris, such as mud, water, grease, oil, sawdust, powders, etc. • Highly-polished or freshly-waxed floors. • Transitioning from one surface another, such as walking from a carpeted surface to a smooth surface like tile. • Sloped walking surfaces. • Loose floor tiles, loose or unanchored floor mats, and loose floor covers. • Wet, muddy, or inappropriate footwear. • Environmental factors, such as rain, snow, and frost. • Mounting and dismounting equipment improperly. • Climbing ladders with wet, muddy, or greasy shoes. • Mark swinging doors with "in" and "out" signage. ## The main causes of trips include: • Uncovered cables, wires, or extension cords. • Cluttered walkways. - Open cabinets and desk drawers. • Changes in elevation, such as unmarked steps. • Damaged or nonuniform steps and ladders. Other conditions and factors that may contribute to slips, trips, and falls include: • Poor lighting. • Use of bulky equipment and personal protective equipment (PPE). • Improper material handling techniques. • Loud noise or distractions. • Medication or drug and alcohol effects. …

[5] Housekeeping Checklist

Page 2

Open source document

Source excerpt

# SAFETY WALKAROUND CHECKLIST HOUSEKEEPING (cont.) ## HAZARD IDENTIFICATION, REMOVAL, AND CLEANUP (cont.) NOTES - Scrap and debris are piled neatly. - Materials, waste, or tools are not thrown from buildings or structures to areas where workers may be located. [1513(g)] - Any object protruding at head height has been removed or flagged. - Protective caps are used on exposed rebar. [1712(a)] ## BULK MATERIAL STORAGE - All piled or stacked material is stable and cannot fall, slip, or collapse. [1549] - The face of a pile of bags (containing cement or other material) more than 5 feet high is tapered back, or the sacks are tied in horizontal layers to prevent them from falling or collapsing. [1549(b)] - Lumber piles are no more than 16' high if handled manually or 20' high if handled by equipment. Headpieces, crosspieces, or other means are used to prevent slipping, tipping, or collapsing. [1549(c)] - Piles of bricks, tiles, masonry blocks, and similar materials are stabilized by the use of headers at least every sixth layer. [1549(a)] - Brick stacks are not over 7 feet high. Brick stacks over 4 feet high are tapered back. [1549(a)] - Masonry stacks over 6 feet high are tapered back. [1549(a)] - The way that material is going to be taken off the pile is planned at the time the material is first stored. - Workers and their equipment have room to move material off a pile. - Material is piled on surfaces that will hold its weight. [1549(f)] - Material is piled on ground stable enough for a heavy load (not too near an excavation). - Pipe or rod is stored in racks if more than one layer high. - Surplus materials are returned to the stockpile. ## HAZARDOUS MATERIAL STORAGE AND DISPOSAL - Flammable material is always stored in closed containers. [1513(e)] - Incompatible chemical products (which may cause a hazardous reaction if they come in contact) are not stored together. [1549(g) and 1931(b)] - Smoking is prohibited in flammable liquid storage areas.…

[6] Toolbox Talk: Slips, Trips, and Falls

Page 1

Open source document

Source excerpt

# SLIPS, TRIPS, AND FALLS Date Posted: 01/30/2024 According to the Bureau of Labor Statistics (BLS), nearly one-third of reportable injuries and 40% of fatalities in construction result from slips, trips, and falls nationally. These injuries result in 50% more days away from work than other injuries. Slips, trips, and falls are among the top three causes of work-related injury. A worker doesn't have to fall from a high level to suffer fatal injuries; 136 workers were killed in falls on the same level in 2020. However, each of these describes a slightly different kind of incident: • Slips happen when traction's lost between the bottom of your shoe and whatever you're stepping on. This can be caused by uneven terrains like wet ground, ice, or mud; wet or greasy surfaces; poor footwear; and other issues. In addition, slips are more likely to occur when a worker hurries or runs, wears the wrong footwear or ignores where they're walking. • A trip is when someone catches their foot against an object or uneven terrain, causing them to trip and fall. Poor lighting misplaced tools, debris like gravel or nails, and improper safety gear also cause tripping hazards. A fall is a much more severe injury where someone lands too hard on their feet, torso, or head and is knocked over. NOTE: CARRYING, PUSHING, OR PULLING ITEMS THAT ARE HEAVY OR AWKWARD CAN ALSO MAKE SLIPS, TRIPS, AND FALLS MORE LIKELY. THESE ACTIONS CAN AFFECT THE ABILITY TO MAINTAIN BALANCE AND THE AMOUNT OF TRACTION NEEDED WHERE THE FEET MEET THE GROUND. ## COMMON CAUSES OF SLIP, TRIP, AND FALL ACCIDENTS - Slick spots or oily spots on walking surfaces • Clutter - Debris • Unsafe stairs or ladders • Improperly secured ladders or scaffolding parts • Improperly sloped walking surfaces • Loose or unsecured flooring • Ramps without skid or slip-resistant surfaces - Accessing/Egressing vehicles and equipment - Loose surfaces such as gravel or crushed rock • Weather-related hazards • Uncovered or unse…

[7] Toolbox Talk: Slips, Trips, and Falls

Page 2

Open source document

Source excerpt

# SLIPS, TRIPS, AND FALLS (cont.) ## CONSTRUCTION AREAS AT HIGH RISK FOR SLIP, TRIP, AND FALL ACCIDENTS (cont.) • Material storage: All materials should be stored away from walkways, not block doors or exits. Be sure that items are not impeding the flow of people. Ensure that things are not stacked so high that they become hazardous. OSHA has requirements for particular types of materials and how they will be stored. ## HOW CAN SLIPS, TRIPS, AND FALLS BE PREVENTED? • Maintain Good Housekeeping - Keep Walking and Working Areas Clear of Debris: Don't leave trip hazards in the work area. Keep your work area clear of debris on the ground, gravel, loose materials, and anything else that could cause someone to step wrong. Debris can be hazardous if it includes nails or other sharp objects. You may need to allocate time for cleaning up messy walking areas throughout the day. Outdoor surfaces should be kept clean and dry. They may be treated with sand, salt, and anti-skid adhesive when necessary. Indoor surfaces should be secured with non-slip floor mats that allow people to clean their shoes. Heavily treaded construction work boots and shoes can track in nails and other potential hazards. • Identify and Take Precautions for Wet and Slippery Conditions: During certain seasons, construction sites can be especially hazardous due to ice, snow, and other wet weather conditions. Clear walkways regularly-at least once every 12 hours during snowfall or icy conditions and periodically in dryer months if water is allowed to collect. Keep walkways and other surfaces as free of slippery materials like mud and precipitation as possible, and implement a "wet floor" signage policy where wet areas are restricted from access until made non-hazardous. • Use the Right Footwear: Using proper footwear is one of the most effective ways of preventing slips, trips, and falls onsite. Regarding work boots, stick to ones with slip-resistant soles, as these offer the best traction on smooth or…

[8] Toolbox Talk: Housekeeping

Page 1

Open source document

Source excerpt

CPWR TOOLBOX THE CENTER FOR CONSTRUCTION RESEARCH AND TRAINING TALK # Housekeeping Housekeeping refers to making sure materials are in good condition and keeping the areas we work in and walk in clean, orderly, sanitary, and dry. Bad housekeeping is dangerous at any time. It can lead to production delays, property damage, and higher costs. ## Sharon's Story Sharon, a carpenter, was doing framing for a custom-sized space on the second story of a house. A lot of wood pieces, scraps, and sawdust had accumulated around the sawhorses, power tools, cords, and piles of materials. When leaving for the day, she tripped over some of the items on the floor and fell down the stairwell, injuring her neck. - What could have been done to prevent this incident? - Does your worksite have a lot of lumber, debris, or flammable materials lying around? - How often are materials organized and placed where they belong? ## Remember This - Keep floors dry, clean, and clear of waste. - Keep workplaces well-lighted. - Keep hoses, power cords, and welding leads out of heavily travelled walkways or areas. - Keep materials away from openings, roof edges, excavations, and trenches. - Keep all work areas, walkways, and stairs in and around buildings or other structures clear. - Don't allow materials or garbage to build up. Remove unused materials. - Don't block emergency exits, fire equipment, or first aid stations. ➤ Don't store chemicals and gases near heat sources or electrical equipment. - Place, stack, or store materials and equipment where they will not cause injury to workers. - Provide separate, covered containers for collecting different wastes, such as trash, oily rags, dry rags, and flammable or hazardous materials (acids, harsh or harmful dusts, etc.). How can we stay safe today? What will we do at the worksite to promote housekeeping? 1. 2. OSHA Regulation: 1926.25 ©2017, CPWR-The Center for Construction Research and Training. All rights reserved. CPWR …

[9] Slips, Trips, and Falls - Module 2

Page 10

Open source document

Source excerpt

# Maintaining Work Areas: Housekeeping # Housekeeping ● Keep walkways, aisles, and stairs clear of materials, equipment, and other hazards. - Cover or secure (or suspend overhead on construction sites) cables, cords, wires, and hoses away from walkways and other paths of travel. - Make sure rugs or mats are flat and not bunched up. Pathway is clearly marked and free of obstructions. Washington State Department of Labor & Industries 10

[10] IHSA Safety Tool Box talks

Page 88

Open source document

Source excerpt

# Housekeeping List housekeeping hazards on site. ## Explain dangers We all know how fast rubbish builds up on a site- scrap lumber, broken bricks, pieces of drywall, strap-bands, and packaging. How can you concentrate on your work when you're worried about slipping, falling, or tripping over garbage and debris? Production and installation time go up while quality tails off. Every year, poor housekeeping and storage practices cause many accidents and injuries. Construction rubbish is often irregular in shape, hard to handle, and full of sharp objects. One of the biggest problems is packaging. Too often it gets removed from material and left wherever it falls. This creates tripping and slipping hazards. It also makes other hazards hard to see. Even worse, it invites more mess. When a site isn't cleaned up, no one cares about leaving garbage where it drops. When that happens, you can't see faulty wiring, protruding nails, damaged flooring, and missing scaffold planks. Clutter left around work and travel areas also makes it difficult to use material-handling equipment. As a result, more material gets handled manually, which increases the risk of injury and property damage. Housekeeping means cleaning up scrap and debris, putting it in containers, and making sure the containers are emptied regularly. It also means proper storage of materials and equipment. Effective housekeeping and storage will prevent incidents and injuries. ## Identify controls • Keep work and travel areas kept tidy, well-lit, and ventilated. Clean up as work proceeds. - Keep equipment and the areas around equipment free of scrap and debris. - Pick up, store, or dispose of tools, material, or debris that may cause tripping or other hazards. - Keep stairways, passageways, ramps, and other travel areas clear at all times. • Secure loose or light materials stored on roofs and open floors to keep them from blowing away in the wind. Resecure the material after removing any of it. • Nev…

[11] Housekeeping Checklist

Page 4

Open source document

Source excerpt

# SAFETY WALKAROUND CHECKLIST HOUSEKEEPING (cont.) ## SANITATION (cont.) NOTES ## ENVIRONMENT - Lighting and ventilation are adequate. [1523] - Burned out lights are reported and replaced. ## WORK PRACTICES - Housekeeping occurs constantly on the job, not just once a week or at the end of the project. [1513(a)] - Everyone does housekeeping, not just laborers. - Workers pick up anything they see lying around that can trip a person or fall on them. - Extension cords, lines, welding leads, hoses, etc. are coiled up when not in use. - Tools are returned to the gang box or tool room. California Tailgate Training Housekeeping-Page 4

[12] Housekeeping Inspection – Safety Checklist

Page 2

Open source document

Source excerpt

# Housekeeping Inspection - Safety Checklist (cont.) <table><tr><th>18. Are combustibles and flammables stored in appropriate, approved containers?</th><th></th><th></th><th></th><th></th><th></th></tr><tr><td>Storage</td><td>Yes</td><td>No</td><td>N/A</td><td>Comments &amp; Action Needed</td><td>Completed Date</td></tr><tr><td>19. Are boxes and pallets stacked in an orderly fashion?</td><td> </td><td> </td><td></td><td></td><td></td></tr><tr><td>20. Are storage materials placed in such a manner not to interfere with workers or the flow of materials?</td><td></td><td></td><td>ㅁㅁㅁ</td><td></td><td></td></tr><tr><td>21. Are all storage areas clearly marked?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>Machinery, Tools, &amp; Equipment</td><td>Yes</td><td>No</td><td>N/A</td><td>Comments &amp; Action Needed</td><td>Completed Date</td></tr><tr><td>22. Are tools and/or equipment stored in designated areas when not in use?</td><td> </td><td></td><td></td><td></td><td></td></tr><tr><td>23. Are individual work areas kept clean, organized and orderly?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>24. Are machinery and/or equipment checked weekly for leaks and any leaks repaired and cleaned up?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>25. Are tools, machinery and equipment cleaned on a regular basis?</td><td></td><td></td><td>ㅁㅁㅁ</td><td></td><td></td></tr><tr><td>Waste Disposal &amp; Chemicals</td><td>Yes</td><td>No</td><td>N/A</td><td>Comments &amp; Action Needed</td><td>Completed Date</td></tr><tr><td>26. Is all trash and/or waste collected and placed in designated and/or appropriate containers?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>27. Is all trash/waste taken out for collection on a regular basis?</td><td></td><td></td><td></td><td></td><td></td></tr><tr><td>28. Are separate approved containers provided to separate waste (i.e. trash, oil, used rags, hazardous waste, flammables, etc.)?</td><td><…

Related Q&A

Keep exploring.

Human questionGeneral

for a site attendance, what questions should be asked?

During a site attendance or site visit, the key safety objective is to confirm that hazards have been identified, risks assessed, and effective controls implemented before and during the work. A strong site visit should test whether the work is planned, supervised, communicated, and carried out in compliance with the

Read the thread
Human questionGeneral

Create a safety jobsite inspection checklist for entire building and construction site

Here is a sample safety checklist for a building and construction job site, designed for use in Texas. This checklist is intended to be a starting point and should be customized to fit the specific hazards and conditions of your job site. *Job Site Inspection Checklist** *Date:** *Inspector:** *Site Location:**

Read the thread
Human questionUS

Write a toolbox talk on safety

A strong toolbox talk on workplace health and safety should focus on identifying hazards before work starts, assessing the level of risk, following site-specific safe work procedures, using the right PPE, reporting incidents and near misses promptly, knowing emergency actions, complying with OSHA requirements, and

Read the thread
Human questionUS

Regs

Safety Regulations and Compliance Standards =========================================== This document outlines the key safety regulations and compliance standards applicable to both general industry and construction, drawing from federal and state-specific guidelines. It emphasizes the importance of adherence to these

Read the thread
Discussion thread

Add your experience.

Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.

New contributions are temporarily closed while the moderation queue is configured.

Community answers(0)

No community answers have been approved yet.

Comments on Rosie's answer(0)

No comments have been approved yet.

Ready to put operational safety to work?

Join 400K users across 150K sites already on SALUS.

Request a demo

No commitment · 30-minute personalized walkthrough