Tool box talk for boom lift inspection procedures referencing ANSI A92.22

Boom Lift Pre-Start Inspection, Maintenance, and Safe Operating Procedures ===========================================================================

Date: 2025-11-03

Duration: \[DURATION] minutes

Presenter: \[PRESENTER NAME]

Location: \[LOCATION]

Objective

---

To ensure all personnel understand the importance of pre-start inspections, proper maintenance, and safe operating procedures for boom lifts, in accordance with ANSI A92\.22 and OSHA regulations.

Introduction

---

This toolbox talk covers the essential safety practices for operating boom lifts. Boom lifts, when properly used and maintained, are valuable tools. However, they pose significant risks if pre-use inspections and safe operating procedures are not followed. This talk will cover key inspection points, maintenance guidelines, and safe operating procedures to prevent accidents and ensure compliance with ANSI A92\.22 and OSHA regulations.

Key Points

---

• Pre-Start Inspection: A thorough pre-start inspection is critical. Before each shift, inspect all components of the boom lift to ensure they are in safe working condition. Use the Aerial Lift Pre-Use Inspection Checklist as a guide.
  • Check steps and step fastenings
  • Inspect work platform and floor landings
  • Verify rails, rail supports, and fastenings are secure
  • Examine rollers and slides for proper function
  • Check belt and belt tension
  • Ensure handholds and fastenings are in good condition
  • Confirm guardrails are intact
  • Verify proper lubrication
  • Test limit switches
  • Inspect tires for wear and pressure
  • Confirm horn, warning signs, backup alarm, and lights are functional
  • Check illumination
  • Inspect drive pulley, bottom pulley, and pulley supports
  • Verify the restraining device is in place
  • Ensure operator is protected from potential falls
  • Check fluids and hoses (coolant, hydraulic, etc.)
  • Verify motor and oil level
  • Inspect propane tank (if equipped)
  • Check driving mechanism, operating controls, and brakes
  • Test electrical switches
  • Look for vibration and misalignment
  • Inspect the battery
• Maintenance: Regular maintenance is essential for the safe operation of boom lifts. Follow the manufacturer's recommendations for maintenance schedules and procedures. Only trained and qualified personnel should perform maintenance tasks.
  • Keep maintenance records up-to-date
  • Address any issues identified during inspections promptly
  • Ensure all repairs are performed to the manufacturer's specifications
  • Use only approved replacement parts
• Safe Operating Procedures: Adhere to safe operating procedures at all times. This includes understanding the boom lift's limitations, proper setup, and safe maneuvering. [1]

[3]

• Ensure the ground is level and stable before operating the lift
• Set outriggers, brakes, and wheel chocks, even on level surfaces
• Be aware of overhead obstructions and power lines
• Never exceed the boom lift's weight capacity
• Operate controls smoothly and avoid sudden movements
• Maintain a safe distance from other workers and equipment
• Before moving an aerial lift for travel, the boom(s) shall be inspected to see that it is properly cradled and outriggers are in stowed position
• Fall Protection: Fall protection is mandatory when working in a boom lift. Always wear appropriate fall arrest equipment and attach the lanyard to a designated anchor point. [1]

[1]

• Inspect fall arrest equipment before each use
• Ensure the lanyard is in good condition and properly attached
• Stand on the floor of the bucket and do not climb on or lean over the guardrails
• Electrical Safety: Be aware of electrical hazards when operating a boom lift near power lines. Maintain a safe distance and use insulated lifts when necessary. [3]
• Identify all overhead power lines before starting work
• Maintain a minimum of 10 feet distance from live power lines
• Use insulated boom lifts when working near energized lines
• Ensure the insulated portion of an aerial lift is not altered in any manner that might reduce its insulating value
• Competent Person: Ensure that a competent person conducts regular inspections and maintenance of the boom lift. This includes monthly inspections and annual inspections as specified by the manufacturer and OSHA standards. [2]

[2]

• Training of employees in the operation and inspection of working platforms shall be done by a competent person
• A maintenance inspection and, where necessary, a test shall be made of each platform installation every 30 days, or where the work cycle is less than 30 days such inspection and/or test shall be made prior to each work cycle. This inspection and test shall follow procedures recommended by the manufacturer, and shall be made by a competent person.

Hazard Identification

---

• Mechanical Failures: Boom collapse, platform instability, leading to falls and serious injuries.
• Electrical Hazards: Contact with overhead power lines can cause electrocution or severe burns.
• Falls from Height: Lack of proper fall protection can result in serious injury or death.
• Overloading: Exceeding the weight capacity can cause the boom lift to become unstable and collapse.
• Unstable Ground Conditions: Operating on uneven or soft ground can cause the boom lift to tip over.

Control Measures

---

• Conduct thorough pre-start inspections using a checklist.: Use the Aerial Lift Pre-Use Inspection Checklist to verify all components are in safe working order before each shift. Document the inspection.
• Implement a regular maintenance program.: Follow the manufacturer's recommended maintenance schedule. Keep records of all maintenance activities.
• Ensure operators are properly trained and certified.: Only allow trained and authorized personnel to operate boom lifts. Provide refresher training as needed.
• Use fall protection equipment.: Require all occupants of the boom lift to wear a full-body harness and lanyard attached to a designated anchor point.
• Maintain safe distances from power lines.: Identify and avoid all overhead power lines. Use insulated lifts when working in proximity to electrical hazards.
• Assess ground conditions before operation.: Ensure the ground is level and stable. Use outriggers and wheel chocks as necessary.

Personal Protective Equipment (PPE) Requirements

---

• Hard Hat: Wear a Class A hard hat to protect against head injuries from falling objects or contact with overhead structures. Physically altered, painted, or damaged hard hats shall not be worn. [4]

[4]

• Inspect the hard hat for damage before each use
• Ensure the hard hat fits properly and is adjusted correctly
• Do not wear baseball caps underneath
• Safety Glasses: Use Z87\.1 safety glasses to protect your eyes from dust, debris, and other flying particles. Use goggles when working around dust, chemicals. Face shields do not protect eyes from flying object high impacts, must use Z87\.1 safety glasses underneath [4]

[4]

• Inspect safety glasses for scratches or damage
• Ensure safety glasses fit snugly and provide adequate coverage
• Work Boots: Wear ANSI Z41-1999 or ASTM 2412 \& 2413 certified footwear with toe protection to prevent foot injuries from crushing hazards. Employee Provided / Employer must require [4]

[4]

• Ensure work boots are in good condition with adequate tread
• Check for any signs of damage or wear
• Lace boots tightly for proper support
• Fall Arrest Harness: A full-body harness is required when operating a boom lift to protect against falls. Inspect fall arrest equipment before each use
• Inspect the harness for any signs of damage or wear
• Ensure the harness fits properly and is adjusted correctly
• Attach the lanyard to a designated anchor point

Group Discussion

---

Discuss the following questions:

1. What are the most common hazards you encounter when operating a boom lift?
2. What steps can we take to improve our pre-start inspection process?
3. How can we better communicate potential hazards to other workers on the job site?

Emergency Procedures

---

1. In the event of a mechanical failure, immediately lower the boom lift to the ground if possible.
2. If contact with a power line occurs, stay inside the platform and wait for emergency personnel to de-energize the line.
3. In case of a fall, activate the emergency alarm and call for help. Ensure a rescue plan is in place.

Summary

---

Recap of main points:

• Always perform a thorough pre-start inspection using the provided checklist.
• Adhere to all safe operating procedures and guidelines.
• Use required PPE, including hard hat, safety glasses, work boots, and fall arrest harness.
• Be aware of potential hazards and take steps to mitigate them.

Remember: Safety First: Inspect, Maintain, Operate Safely!

Report all hazards, near-misses, and incidents to your supervisor immediately.

Safety powered by SALUS