Skip to content
All safety questions
Asked by a personUnited Statesen-US

can you make me a qc checklist for plumbing?

A person submitted this question to Rosie's free generator. The asker's identity is neither imported nor published.

Rosie's answer

Published by SALUS

A practical quality control checklist for plumbing installation and inspection should cover code compliance, materials, workmanship, testing, leak prevention, fixture installation, and worker safety. Start with a documented hazard and task assessment for the work area, verify applicable plumbing/building code edition and approved plans, confirm permits/required inspections, and ensure installation follows manufacturer instructions and approved materials listings. For safety management, perform a workplace walk-through, identify physical and health hazards, and apply engineering or administrative controls before relying on PPE. [5] [6] [3] [7]

  • Verify the governing plumbing, building, mechanical, fuel gas, firestopping, and energy code editions adopted by the authority having jurisdiction.
  • Confirm approved drawings, specifications, permits, rough-in inspection requirements, test requirements, and final inspection requirements are available on site.
  • Check that all pipe, fittings, valves, fixtures, supports, sealants, and devices are approved for the intended service, pressure, temperature, and environment.
  • Verify materials are new or acceptable for reuse where permitted, free from visible damage, deformation, corrosion, contamination, and incompatible mixing of systems.
  • Confirm potable-water components are suitable for drinking-water service where required, and that drainage, vent, storm, and gas materials are not interchanged.
  • Ensure manufacturer installation instructions are available for fixtures, carriers, valves, pumps, water heaters, interceptors, and specialty devices.
  • Confirm required certifications/listings are present where applicable, and that PPE used on site meets recognized standards.
  • Document lot numbers, model numbers, pressure ratings, and inspection status for traceability.

[7]

  • Check pipe routing against plans for correct size, slope, invert elevations, vent connections, cleanout locations, valve accessibility, and required clearances from structure and other trades.
  • Verify piping is properly aligned, adequately supported, protected from abrasion, and isolated from dissimilar materials where galvanic corrosion could occur.
  • Confirm penetrations through walls, floors, and rated assemblies are sleeved/sealed correctly and firestopped where required.
  • Inspect joints for correct preparation and assembly: cut ends square, burrs removed, threads clean, solvent cement or joining method compatible with the piping system, and no evidence of overheating, under-insertion, or cross-threading.
  • Ensure valves, unions, strainers, traps, backflow devices, and access panels are installed in the correct orientation and remain serviceable after finishes are installed.
  • Verify no dead legs, unnecessary offsets, sags, back-pitched drainage piping, or concealed unapproved joints.
  • Check fixture rough-in dimensions, anchorage, level/plumb condition, trap seals, venting, and accessibility clearances.
  • Confirm protection plates/guards are installed where piping passes through framing and may be exposed to nails or screws.

Pressure testing, leak prevention, and inspection points:

  • Test water, drain-waste-vent, gas, and specialty piping systems using the method, medium, pressure, duration, and witness requirements required by the adopted code and manufacturer instructions.
  • Before testing, isolate sections as needed, cap/openings securely, verify gauges are calibrated and readable, and inspect visible joints, valves, and fittings.
  • Do not conceal piping until required rough-in inspections and tests are complete and accepted.
  • For leak prevention, inspect all joints during and after testing, verify proper torque/tightening where applicable, and recheck after thermal cycling or system startup.
  • Where a pressure-retaining assembly or protective enclosure is tested, visually inspect seams, closures, fittings, valves, and other components before the test; remove from service if leakage or unacceptable pressure loss is found.
  • Use a soap-and-water solution for leak location on appropriate systems where permitted; never use open flame for leak checking.
  • Flush, disinfect, and purge systems as required before placing them into service, especially potable-water systems.

[12] [9] [9] Fixture and system-specific quality checks:

  • Water supply: verify pipe sizing, isolation valves, hammer arrestors where required, backflow protection, pressure-reducing devices if needed, and protection from freezing or overheating.
  • Sanitary drainage and vent: verify required slope, trap arm limits, vent sizing and termination, cleanouts, trap seals, and no cross-connections with storm or potable systems.
  • Fixtures: verify secure mounting, proper sealing to walls/floors, correct trap and stop-valve installation, functional drainage, proper hot/cold orientation, and no rocking, leakage, or overflow defects.
  • Water heaters and equipment: verify seismic/support requirements where applicable, temperature and pressure relief valve installation, discharge piping termination, combustion air/venting where fuel-fired, drain pan/drain where required, and access for service.
  • Pumps and specialty equipment: verify rotation, isolation, vibration control, electrical coordination, and startup settings.
  • Final inspection: operate every fixture and valve, confirm flow, drainage, vent performance, absence of leaks, labeling, access, and completion of punch-list items.

Health and safety precautions, hazard identification, and PPE:

  • Conduct and document a task-based hazard assessment before work begins and whenever the job changes, new equipment/processes are introduced, or an incident occurs.
  • Typical plumbing hazards include cuts from sharp edges, flying particles from cutting/grinding, chemical splashes from primers, cements, cleaners, and descalers, wet/slippery surfaces, puncture hazards, electrical exposure, noise, dust, confined spaces, hot work, manual handling strains, trenching/excavation hazards, and biological exposure from sewage.
  • Use engineering and administrative controls first: isolate energy sources, ventilate work areas, control ignition sources, maintain housekeeping, barricade wet areas/openings, and coordinate with other trades.
  • Provide and enforce PPE matched to the hazard: safety glasses/goggles/face shields for cutting, grinding, dust, and splash hazards; gloves selected for cut, abrasion, puncture, temperature, or chemical resistance; sturdy slip-resistant safety footwear with toe and puncture protection as needed; hard hats where overhead/electrical hazards exist; hearing protection where noise exceeds limits; and respiratory protection when required by exposure assessment.
  • Inspect PPE regularly, ensure proper fit, train workers on use/care/limitations, and replace damaged or worn PPE promptly.
  • For respirator use, maintain a written respiratory protection program, complete medical evaluations and fit testing, and document training and inspections.

[10] [4] [4] [2] [1] [8] Applicable regulatory and code requirements should be verified against the authority having jurisdiction for the project location. At minimum, the checklist should reference the adopted plumbing code, building code, fuel gas code if applicable, mechanical code where equipment interfaces exist, fire-resistance/firestopping requirements, manufacturer instructions, and OSHA construction safety requirements for worker protection. For PPE and hazard assessment programs, the supplied sources specifically reference OSHA 29 CFR 1910\.132, 1910\.134, 1910\.95, construction standard 29 CFR 1926\.65 Appendix A, and Washington WAC 296-800-160\. In practice, plumbing QC should also confirm compliance with local amendments, permit conditions, inspection sign-offs, and utility/public health requirements for potable water, cross-connection control, and sanitary connections. [3] [4] [1] [11] [5]

Recommended inspection record fields:

  • Project/location, permit number, code edition, inspector, date, and inspection stage.
  • System type and area inspected.
  • Material/manufacturer/model/size/pressure rating verification.
  • Support spacing, slope, clearances, penetrations, firestopping, and accessibility checks.
  • Test medium, test pressure, start/end time, gauge identification/calibration status, and pass/fail result.
  • Deficiencies found, corrective actions, retest date, and final acceptance signature.
  • Worker hazard assessment, PPE issued, training confirmation, and any incident/near-miss notes.

[7]

12 source record(s)

Sources used for this answer

[1] Occupational Safety and Health Standards (OSHA 29 CFR 1910) - 1910.120 App A - Personal Protective Equipment Test Methods

Page 3

Open source document

Source excerpt

# Occupational Safety and Health Administration (cont.) ## Appendices to $ 1910.120 - Hazardous Waste Operations and Emergency Response (cont.) - 6.1 Prior to each test, the tester shall perform a visual inspection of the suit. Check the suit for seam integrity by visually examining the seams and gently pulling on the seams. Ensure that all air supply lines, fittings, visor, zippers, and valves are secure and show no signs of deterioration. - 6.1.1 Seal off the vent valves along with any other normal inlet or exhaust points (such as umbilical air line fittings or face piece opening) with tape or other appropriate means (caps, plugs, fixture, etc.). Care should be exercised in the sealing process not to damage any of the suit components. - 6.1.2 Close all closure assemblies. - 6.1.3 Prepare the suit for inflation by providing an improvised connection point on the suit for connecting an airline. Attach the pressure test apparatus to the suit to permit suit inflation from a compressed air source equipped with a pressure indicating regulator. The leak tightness of the pressure test apparatus should be tested before and after each test by closing off the end of the tubing attached to the suit and assuring a pressure of three inches water gauge for three minutes can be maintained. If a component is removed for the test, that component shall be replaced and a second test conducted with another component removed to permit a complete test of the ensemble. - 6.1.4 The pre-test expansion pressure (A) and the suit test pressure (B) shall be supplied by the suit manufacturer, but in no case shall they be less than: (A) = three inches water gauge; and (B) = two inches water gauge. The ending suit pressure (C) shall be no less than 80 percent of the test pressure (B); i.e., the pressure drop shall not exceed 20 percent of the test pressure (B). - 6.1.5 Inflate the suit until the pressure inside is equal to pressure (A), the pre-test expansion suit pressure. Allow at least o…

[2] Personal Protective Equipment (PPE) Checklist

Page 5

Open source document

Source excerpt

# Personal Protective Equipment (PPE) Checklist (cont.) <table><tr><th>62. Have employees been trained on the differences in types of gloves and when and how to use them?</th><th></th><th></th><th></th></tr><tr><td>63. When working with chemicals or corrosives, are employees using the proper type of glove as stated on the Safety Data Sheet (SDS)?</td><td></td><td></td><td></td></tr><tr><td>64. Are the gloves maintained per manufacturer's recommendations?</td><td></td><td></td><td></td></tr><tr><td>65. Are employees who have allergies to certain gloves given alternative gloves?</td><td></td><td></td><td></td></tr><tr><td>66. Do gloves fit properly and are they rated for the specific task being performed?</td><td></td><td></td><td></td></tr><tr><td>67. Is damaged, defective or worn hand protection properly discarded and replaced?</td><td></td><td></td><td></td></tr><tr><td>Hearing Protection (N/A )</td><td>Yes</td><td>No</td><td>Comments</td></tr><tr><td>68. Are there work areas in which employees are exposed to excessively loud noise? 69. Has noise monitoring been conducted by an industrial hygienist or other qualified person?</td><td></td><td></td><td></td></tr><tr><td>70. If one or more employees are exposed to sound levels greater than 85 dBA over an eight hour period, has a written hearing conservation program compliant with 29 CFR 1910.95 been implemented?</td><td></td><td></td><td></td></tr><tr><td>71. Have engineering and/or administrative controls been put in place prior to the use of PPE?</td><td></td><td></td><td></td></tr><tr><td>72. Are noise hazard areas identified with signs?</td><td></td><td></td><td></td></tr><tr><td>73. Are employees required to wear hearing protection in areas where sound levels exceed 85 dBA?</td><td></td><td></td><td></td></tr><tr><td>74. Have employees been trained on the hearing conservation program and how to select, use, wear and care for the hearing protection? 75. Does the hearing protection properly fit the employee?</td>…

[3] Personal Protective Equipment (PPE) Guide

Page 8

Open source document

Source excerpt

# B. What you are required to do The Personal Protective Equipment (PPE) Rule WAC [redacted identifier] says you must • Do a Hazard Assessment for PPE and document it • Select and provide appropriate PPE to your employees (p.10) . Provide training to your employees and document it (p.11) • Make sure your employees use their PPE properly (p.12) • Make sure PPE is in safe and good condition (p.12) You can use the "Guidelines for complying with PPE requirements" checklist on p. 16 to help you with meeting the requirements of the PPE rules. ## 1. Do a Hazard Assessment for PPE and document it Before you can know if your employees need PPE, you must assess your work place for hazards. It will help you select the appropriate PPE for any hazards present or likely to be present. WISHA also requires you to document that you have done a hazard assessment. As the person responsible for conducting the hazard assessment, you are accountable both for the quality and thoroughness of the hazard assessment. 8

[4] Personal Protective Equipment (PPE) Guide

Page 38

Open source document

Source excerpt

# SAMPLE PPE POLICIES # Procedures ## A. Hazard Assessment for PPE (Safety Person or designated person), in conjunction with Supervisors, will conduct a walk-through survey of each work area to identify sources of work hazards. Each survey will be documented using the Hazard Assessment Certification Form, which identifies the work area surveyed, the person conducting the survey, findings of potential hazards, and date of the survey. (Safety Person or designated person) will keep the forms in the (Specify exact location, e.g., your company's business files). (Safety Person or designated person) will conduct, review, and update the hazard assessment for PPE whenever • a job changes • new equipment or process is installed • there has been an accident - whenever a supervisor or employee requests it • or at least every year Any new PPE requirements that are developed will be added into (Name of your business)'s written accident prevention program. ## B. Selection of PPE Once the hazards of a workplace have been identified, (Safety Person or designated person) will determine if the hazards can first be eliminated or reduced by methods other than PPE, i.e., methods that do not rely on employee behavior, such as engineering controls (refer to Appendix B - Controlling Hazards). If such methods are not adequate or feasible, then (Safety Person or designated person) will determine the suitability of the PPE presently available; and as necessary, will select new or additional equipment which ensures a level of protection greater than the minimum required to protect our employees from the hazards (refer to Appendix C - Selection of PPE). Care will be taken to recognize the possibility of multiple and simultaneous exposure to a variety of hazards. Adequate protection against the highest level of each of the hazards will be recommended for purchase. All personal protective clothing and equipment will be of safe design and construction for the work to be performed an…

[5] Personal Protective Equipment (PPE) Guide

Page 16

Open source document

Source excerpt

# Guidelines for complying with PPE requirements Use this checklist to help you comply with the PPE requirements at your work place. You can use the available tools in the far right column to help you accomplish the step. Check off the boxes in the far left column as you complete each step. <table><tr><th>Done</th><th>STEP</th><th>Tools</th></tr><tr><td></td><td>Do a work place walk-through and look for hazards (including potential hazards) in all employees' work spaces and work place operating procedures.</td><td rowspan="3">Checklist #1: PPE Hazard Assessment or Checklist #2: JHA PPE Hazard Assessment</td></tr><tr><td>ப</td><td>Consider engineering, administrative, and/or work practice methods to control the hazards first. Identify those existing/ potential hazards and tasks that require PPE.</td></tr><tr><td></td><td>Select the appropriate PPE to match the hazards and protect employees.</td></tr><tr><td></td><td>Communicate PPE selection to each at-risk employee. Provide properly fitting PPE to each employee required to use it.</td><td></td></tr><tr><td></td><td>Train employees on the use of PPE and document it.</td><td>PPE Training Certification Form</td></tr><tr><td></td><td>Test employees to make sure they understand the elements of the PPE training.</td><td>Sample PPE Training Quiz (optional)</td></tr><tr><td>ப</td><td>Follow up to evaluate effectiveness of PPE use, training, policies, etc. against the hazards at your work place. Yes No All employees have been trained Yes No Employees are using their PPE properly and following PPE policies and procedures Yes No Supervisors are enforcing use of required PPE (If you checked any No boxes, go back through the steps and correct the deficiencies.) Yes No Have things changed at your work place? (e.g., fewer injuries/illnesses)</td><td></td></tr></table> 16

[6] Personal Protective Equipment (PPE) Checklist

Page 4

Open source document

Source excerpt

# Personal Protective Equipment (PPE) Checklist (cont.) <table><tr><th>52. Are Class B hats worn in situations with electrical hazards?</th><th></th><th></th><th></th></tr><tr><td>Foot Protection (N/A )</td><td>Yes</td><td>No</td><td>Comments</td></tr><tr><td>53. Has the proper foot protection been selected and are employees required to use it when exposed to any of the following: Falling objects Punctures Crushing or rolling objects Stubbing Chemical or corrosive contact Electrical shock or burns Slips or falls</td><td></td><td></td><td></td></tr><tr><td>54. Is protective footwear sturdy with nonskid soles?</td><td></td><td></td><td></td></tr><tr><td>55. Is steel-toed or non-metallic safety-toed footwear required to resist impact?</td><td></td><td></td><td></td></tr><tr><td>56. In areas where there is risk for a puncture type injury, do shoes have flexible metal soles or inner shoes?</td><td></td><td></td><td></td></tr><tr><td>57. Do employees wear the proper protective footwear when working in areas that have electrical hazards?</td><td>பப</td><td></td><td></td></tr><tr><td>58. Are employees wearing footwear with slip- resistant soles when working in wet or slippery areas?</td><td></td><td></td><td></td></tr><tr><td>59. Are employees who work in areas that have a risk of chemical or corrosive exposures wearing the appropriate chemical-resistant boots?</td><td></td><td></td><td></td></tr><tr><td>60. Is damaged, defective or worn foot protection properly discarded and replaced?</td><td></td><td></td><td></td></tr><tr><td>Hand Protection (N/A )</td><td>Yes</td><td>No</td><td>Comments</td></tr><tr><td>61. Has the proper hand protection been selected and are employees required to use it when exposed to any of the following: Skin absorption of harmful substances Sever cuts/lacerations Sever abrasions Punctures - Thermal and chemical burns Temperature extremes Corrosive liquids Blood and other potentially infectious materials</td><td></td><td></td><td></td></tr></tabl…

[7] Personal Protective Equipment (PPE) Checklist

Page 3

Open source document

Source excerpt

# Personal Protective Equipment (PPE) Checklist (cont.) <table><tr><th>29. Have medical evaluations been conducted for employees required to wear a respirator?</th><th></th><th></th></tr><tr><td>30. Have employees been fit tested?</td><td></td><td></td></tr><tr><td>31. Has air quality monitoring been conducted by a qualified industrial hygienist?</td><td></td><td></td></tr><tr><td>32. Have employees been trained on the written program and how to use and care for the respirators?</td><td></td><td></td></tr><tr><td>33. Have all training and fit test results been documented and kept on file?</td><td></td><td></td></tr><tr><td>34. Is the face piece clean?</td><td></td><td></td></tr><tr><td>35. Does the exhalation valve allow air to exit mask and not enter?</td><td></td><td></td></tr><tr><td>36. Is the regulator functioning properly?</td><td></td><td></td></tr><tr><td>37. Are the buckles, back plate and straps in good condition?</td><td></td><td></td></tr><tr><td>38. Is the pressure hose in working order?</td><td></td><td></td></tr><tr><td>39. Are the pressure cylinder and all knobs and gauges in good condition and working properly?</td><td></td><td></td></tr><tr><td>40. Are there any air leaks?</td><td></td><td></td></tr><tr><td>41. Is there any visible damage to any part of the mask/respirator, hoses or cylinder?</td><td></td><td></td></tr><tr><td>42. Is the filter or cartridge up-to-date, clean and free of any deterioration/damage?</td><td></td><td></td></tr><tr><td>43. Is the air cylinder fully charged?</td><td></td><td></td></tr><tr><td>Head Protection (N/A )</td><td>Yes No</td><td>Comments</td></tr><tr><td>44. Have employees been trained on how to select, use, adjust, wear and care for their head protection?</td><td></td><td></td></tr><tr><td>45. Is the head protection clean and in good condition?</td><td></td><td></td></tr><tr><td>46. Is the head protection adjusted properly to fit the wearer's head?</td><td></td><td></td></tr><tr><td>47. Are worn straps replace…

[8] Personal Protective Equipment (PPE) Checklist

Page 1

Open source document

Source excerpt

# Personal Protective Equipment (PPE) Checklist <table><tr><th>General PPE Requirements</th><th>Yes</th><th>No</th><th>Comments</th></tr><tr><td>1. Has a hazard assessment to identify and control physical and health hazards been completed? If not, perform a hazard assessment.</td><td></td><td></td><td></td></tr><tr><td>2. Have engineering and/or administrative controls been applied prior to the use of PPE? If not, apply them first if applicable and appropriate.</td><td></td><td></td><td></td></tr><tr><td>3. Has appropriate PPE that matches the hazard been identified and provided to employees for use?</td><td></td><td></td><td></td></tr><tr><td>4. Has the effectiveness of the PPE program been reviewed, updated and evaluated periodically?</td><td></td><td></td><td></td></tr><tr><td>5. Have employees been trained on the use and care of the PPE?</td><td></td><td></td><td></td></tr><tr><td>6. Have employees been trained on the limitations of the PPE?</td><td></td><td></td><td></td></tr><tr><td>7. Is the PPE training documented and kept on file?</td><td></td><td></td><td></td></tr><tr><td>8. Are supervisors enforcing the use of required PPE?</td><td></td><td></td><td></td></tr><tr><td>9. Is PPE inspected regularly and properly maintained?</td><td></td><td></td><td></td></tr><tr><td>10. Is worn and damaged PPE removed from service and replaced?</td><td></td><td></td><td></td></tr><tr><td>11. When the following type of PPE is necessary, is the employer providing and paying for the PPE as stated by the OSHA standard 1910.132? Metatarsal foot protection - Rubber boots with steel toes Non-specialty-toe footwear (i.e. steel toe shoes/boots) if the employer does not permit it to be worn off the job site Non-prescriptive eye protection Prescriptive eyewear inserts/lenses for full face respirators Goggles and face shields Firefighting PPE (i.e. helmet, boots, gloves, full gear, proximity suits, etc.) Hard hats Hearing protection Welding PPE</td><td></td><td></td><td></td></tr></t…

[9] Safety and Health Regulations for Construction (OSHA 29 CFR 1926) - 1926.65 App A - Personal Protective Equipment Test Methods

Page 1

Open source document

Source excerpt

U.S. DEPARTMENT OF LABOR # Occupational Safety and Health Administration - Part Number: 1926 - Part Number - Title: Safety and Health Regulations for Construction - Subpart: 1926 Subpart D - Subpart Title: Occupational Health and Environmental Controls Standard - Number: 1926.65 AppA - Title: Personal Protective Equipment Test Methods - GPO Source: e-CFR Note: The following appendices serve as non-mandatory guidelines to assist employees and employers in complying with the appropriate requirements of this section. However 1926.65(g) makes mandatory in certain circumstances the use of Level A and Level B PPE protection. This appendix sets forth the non-mandatory examples of tests which may be used to evaluate compliance with 1926.65(g)(4)(ii) and (iii). Other tests and other challenge agents may be used to evaluate compliance. A. "Totally-encapsulating chemical protective suit pressure test" - 1.0- Scope - 1.1 This practice measures the ability of a gas tight totally-encapsulating chemical protective suit material, seams, and closures to maintain a fixed positive pressure. The results of this practice allow the gas tight integrity of a totally-encapsulating chemical protective suit to be evaluated. - 1.2 Resistance of the suit materials to permeation, penetration, and degradation by specific hazardous substances is not determined by this test method. - 2.0 Definition of terms - 2.1 "Totally-encapsulated chemical protective suit (TECP suit)" means a full body garment which is constructed of protective clothing materials; covers the wearer's torso, head, arms, legs and respirator; may cover the wearer's hands and feet with tightly attached gloves and boots; Submit Feedback

[10] Personal Protective Equipment (PPE) Guide

Page 17

Open source document

Source excerpt

# Option 1 # Hazard Assessment For PPE Use with WAC [redacted identifier] Personal Protective Equipment (PPE) This tool can help you do a hazard assessment to see if your employees need to use personal protective equipment (PPE) by identifying activities that may create hazards for your employees. The activities are grouped according to what part of the body might need PPE. You can make copies, modify and customize it to fit the specific needs of your particular work place, or develop your own form that is appropriate to your work environment. This tool can also serve as written certification that you have done a hazard assessment as required by WAC 296-800-[redacted postal code] Document your hazard assessment for PPE. Make sure that the blank fields at the beginning of the checklist (indicated by *) are filled out (see below, Instructions #4). ## Instructions: 1. Do a walk through survey of each work area and job/task. Read through the list of work activities in the first column, putting a check next to the activities performed in that work area or job. 2. Read through the list of hazards in the second column, putting a check next to the hazards to which employees may be exposed while performing the work activities or while present in the work area. (for e.g., work activity: chopping wood; work-related exposure: flying particles). 3. Decide how you are going to control the hazards. Try considering engineering, work place, and/or administrative controls to eliminate or reduce the hazards before resorting to using PPE. If the hazard cannot be eliminated without using PPE, indicate which type(s) of PPE will be required to protect your employee from the hazard. 4. Make sure that you complete the following fields on the form (indicated by *) to certify that a hazard assessment was done: *Name of your work place *Address of the work place where you are doing the hazard assessment *Name of person certifying that a workplace hazard assessment was done *Da…

[11] Personal Protective Equipment (PPE) Checklist

Page 2

Open source document

Source excerpt

# Personal Protective Equipment (PPE) Checklist (cont.) <table><tr><th>12. If the employee provides his/her own PPE, is it adequate to protect the worker from hazards in the workplace?</th><th></th><th></th><th></th></tr><tr><td>Eye and Face Protection (N/A )</td><td>Yes</td><td>No</td><td>Comments</td></tr><tr><td>13. Do employees perform hammering, cutting, grinding, sanding and/or masonry work that produces or could produce particles/dust or debris?</td><td>ㅁㅁㅁ</td><td></td><td></td></tr><tr><td>14. Do employees handle chemicals that could splash into their eyes or face?</td><td></td><td></td><td></td></tr><tr><td>15. Do employees work with wet or powdered cement?</td><td></td><td></td><td></td></tr><tr><td>16. Do employees weld?</td><td></td><td></td><td></td></tr><tr><td>17. Do employees work in dusty or windy conditions?</td><td></td><td></td><td></td></tr><tr><td>If "yes" in response to any of the above eye and face protection questions, are the employees using appropriate PPE as applicable (i.e. safety glasses, goggles, welding shields, face shields, etc.)?</td><td></td><td></td><td></td></tr><tr><td>18. Do safety glasses have frames constructed of plastic or metal with impact-resistant lenses?</td><td></td><td></td><td></td></tr><tr><td>19. Do safety glasses have side shields?</td><td></td><td></td><td></td></tr><tr><td>20. Do safety glasses and goggles completely cover the eyes, eye socket and area surrounding the eyes?</td><td></td><td></td><td></td></tr><tr><td>21. Are goggles tight-fitting?</td><td></td><td></td><td></td></tr><tr><td>22. Are welding shields made of fiberglass or vulcanized fiber with a filtered lens?</td><td></td><td></td><td></td></tr><tr><td>23. Do the filter lenses have the appropriate shade number to protect against specific hazards of the welding work being performed?</td><td></td><td></td><td></td></tr><tr><td>24. Is damaged, defective or worn eye/face protection properly discarded and replaced?</td><td></td><td></td><td></td></…

[12] Safety and Health Regulations for Construction (OSHA 29 CFR 1926) - 1926.65 App A - Personal Protective Equipment Test Methods

Page 2

Open source document

Source excerpt

# Occupational Safety and Health Administration (cont.) - completely encloses the wearer and respirator by itself or in combination with the wearer's gloves and boots. - 2.2 "Protective clothing material" means any material or combination of materials used in an item of clothing for the purpose of isolating parts of the body from direct contact with a potentially hazardous liquid or gaseous chemicals. - 2.3 "Gas tight" means, for the purpose of this test method, the limited flow of a gas under pressure from the inside of a TECP suit to atmosphere at a prescribed pressure and time interval. - 3.0 - Summary of test method - 3.1 The TECP suit is visually inspected and modified for the test. The test apparatus is attached to the suit to permit inflation to the pre-test suit expansion pressure for removal of suit wrinkles and creases. The pressure is lowered to the test pressure and monitored for three minutes. If the pressure drop is excessive, the TECP suit fails the test and is removed from service. The test is repeated after leak location and repair. - 4.0 - Required Supplies - 4.1 Source of compressed air. - 4.2 Test apparatus for suit testing, including a pressure measurement device with a sensitivity of at least 1/4 inch water gauge. - 4.3 Vent valve closure plugs or sealing tape. - 4.4 Soapy water solution and soft brush. - 4.5 Stop watch or appropriate timing device. - 5.0 - Safety Precautions - 5.1 Care shall be taken to provide the correct pressure safety devices required for the source of compressed air used. - 6.0 - Test Procedure - 6.1 Prior to each test, the tester shall perform a visual inspection of the suit. Check the suit for seam integrity by visually examining the seams and gently pulling on the seams. Ensure that all air supply lines, fittings, visor, zippers, and valves are secure and show no signs of deterioration. - 6.1.1 Seal off the vent valves along with any other normal inlet or exhaust points (such as umbilical air line fitti…

Related Q&A

Keep exploring.

Human questionGeneral

for a site attendance, what questions should be asked?

During a site attendance or site visit, the key safety objective is to confirm that hazards have been identified, risks assessed, and effective controls implemented before and during the work. A strong site visit should test whether the work is planned, supervised, communicated, and carried out in compliance with the

Read the thread
Human questionGeneral

rail construction

Rail Construction and Maintenance Safety ======================================== Document Number: \[SWP-NUMBER] Revision Date: \[DATE] Next Review Date: \[NEXT REVIEW DATE] Department: \[DEPARTMENT NAME] 1\. Scope This safe work procedure (SWP) outlines the safety requirements for all rail construction and maintenance

Read the thread
Human questionGeneral

Give me a audit for a construction site

Safety Audit Checklist for Construction Site Hazard Identification and Risk Assessment ====================================================================================== This checklist provides a framework for conducting safety audits on construction sites, focusing on hazard identification and risk assessment. It

Read the thread
Human questionGeneral

de beers safety standards

De Beers Safety Standards and Critical Safety Procedures ======================================================== This document outlines the safety standards and critical safety procedures necessary to ensure a safe working environment and prevent workplace accidents, based on industry best practices and regulatory

Read the thread
Human questionGeneral

Generate HS Manual for Construction Project

Construction Project Health and Safety Manual ============================================= This manual outlines the health and safety requirements for the construction project. It details critical safety procedures, risk assessments, emergency response plans, and compliance measures to ensure a safe working

Read the thread
Discussion thread

Add your experience.

Community answers can add practical context. They are moderated, but they are not SALUS-reviewed safety guidance.

New contributions are temporarily closed while the moderation queue is configured.

Community answers(0)

No community answers have been approved yet.

Comments on Rosie's answer(0)

No comments have been approved yet.

Ready to put operational safety to work?

Join 400K users across 150K sites already on SALUS.

Request a demo

No commitment · 30-minute personalized walkthrough